Jump to content

axle repair?


Tinman22

Recommended Posts

16 minutes ago, terry said:

Isn't that between inner and outer wheel bearing? If weld looks good run it

I think it would have to be. There is no way a bearing would ride on that without getting destroyed in fairly short order. I wonder if it actually broke or if there was just some type of stress fatigue cracking at that machined step and they just threw some weld on it for good measure. Either way that is pretty wild. Would that pass a Federal Annual Inspection or would that be up to the discretion of the inspection mechanic?

Link to comment
Share on other sites

1 hour ago, 67RModel said:

I think it would have to be. There is no way a bearing would ride on that without getting destroyed in fairly short order. I wonder if it actually broke or if there was just some type of stress fatigue cracking at that machined step and they just threw some weld on it for good measure. Either way that is pretty wild. Would that pass a Federal Annual Inspection or would that be up to the discretion of the inspection mechanic?

I don’t think they are pulling hubs on federal inspection and I know PA doesn’t require it for state inspection. So hard to say what the answer is. However it is apparently ok to make repairs like this and places like axle surgeon will come out and repair them. 

Edited by Onyx610
  • Like 1
Link to comment
Share on other sites

It was completly cut off and a piece welded back on. Some say run it. I personally don't trust it and with my luck it will definitely break right on the I-69 michigan scale and send the wheel set rolling into the scale house. So either a housing or a new spindle is the choice.

Here at BEA transpotation failure is not an option, It comes as standard equipment.

Edited by Tinman22
  • Haha 1
Link to comment
Share on other sites

Yea with that information there is no way in hell I would trust or run that spindle. You basically traded the entire cross section of heat treated homogenous material for a fillet weld around the diameter of it. Somebody probably blew in a 6010 root and capped it with 7018 and called it good. Nuts

Link to comment
Share on other sites

Like JoJo said, it might be an insert that is engaged well beyond the weld.  Looking inside, you might be able to tell where the joint is.  If it is the same distance in as the outside seam, I would definitely worry because it is just a butt joint.  If the inside joint is well beyond the outside joint, then it would be the inserted stub he described.  That might be a "legitimate" repair, like Vmac described.

I've never done this to an axle spindle, but have done similar things through the years (drawbar tubes on CNC lathes come to mind).

  • Like 1

"Eagles may soar, but weasels don't get sucked into jet engines."

Link to comment
Share on other sites

1 minute ago, doubleclutchinweasel said:

Like JoJo said, it might be an insert that is engaged well beyond the weld.  Looking inside, you might be able to tell where the joint is.  If it is the same distance in as the outside seam, I would definitely worry because it is just a butt joint.  If the inside joint is well beyond the outside joint, then it would be the inserted stub he described.  That might be a "legitimate" repair, like Vmac described.

I've never done this to an axle spindle, but have done similar things through the years (drawbar tubes on CNC lathes come to mind).

There"s a roving guy in this area the spray welds trailer king pins and you can't even tell after its done even thou you are not allowed to weld on hitches ! So That said if you don't know about it when your looking at it then your likley not going to worry about it! If that axle stub was on a pilot hub wheel and the seal was dri you would have been none the wiser! you would have slammed the brakes on there and a new drum and all done just like normal ! Now that said if that vehicle comes back in a week from now with a wheel seal leak there is a problem!

Just sayin!

  • Like 1
Link to comment
Share on other sites

1 minute ago, fjh said:

There"s a roving guy in this area the spray welds trailer king pins and you can't even tell after its done even thou you are not allowed to weld on hitches ! So That said if you don't know about it when your looking at it then your likley not going to worry about it! If that axle stub was on a pilot hub wheel and the seal was dri you would have been none the wiser! you would have slammed the brakes on there and a new drum and all done just like normal ! Now that said if that vehicle comes back in a week from now with a wheel seal leak there is a problem!

Just sayin!

I've used that spray weld a lot in the machine shop.  Spray it on, turn it to size, and rock on.  It's generally good stuff.  Hard as hell on turning tools!

"Eagles may soar, but weasels don't get sucked into jet engines."

Link to comment
Share on other sites

Its been in the family for years. my wife thinks it happened in the late 90's and her dad had it done in a pinch and just never fixed it right. 

The truck was only used around the county to move asphalt trailers and rarley ever saw 55mph or a full load. I've got it going in on monday for a new spindle at axle surgeons. Really glad that I decided on new brakes and seals otherwise I wouldn't have known it was there. Really can't believe its lasted this long.

  • Like 2
Link to comment
Share on other sites

20 minutes ago, Tinman22 said:

Its been in the family for years. my wife thinks it happened in the late 90's and her dad had it done in a pinch and just never fixed it right. 

The truck was only used around the county to move asphalt trailers and rarley ever saw 55mph or a full load. I've got it going in on monday for a new spindle at axle surgeons. Really glad that I decided on new brakes and seals otherwise I wouldn't have known it was there. Really can't believe its lasted this long.

Well, that should take care of it regardless!

"Eagles may soar, but weasels don't get sucked into jet engines."

Link to comment
Share on other sites

I'm having flashbacks to 2005 when we put our DM dump back on the road with a set of 44's we never used.  It kept blowing 1 wheel seal daily being done by our regular mechanic.  I assembled it without a wheel seal and was checking if it ran true rotating with a dial indicator, the needle wildly jumped and I realized the plug welds were broke loose and it was chucking in the seal ring!

  • Like 2
Link to comment
Share on other sites

12 minutes ago, Tinman22 said:

It might have some time on it but thats about it. Like I said earlier it was only used to move two asphalt trailers around the county from township to township usually half to empty. If it were still on that job I would leave it too.

I had a set of wheels come off the front axle of the lowboy one summer after leaving the tire shop. they rolled up county 13 crossed state 20 one hit a barn the other olmost hit the old woman mowing her grass. After collecting my wheels It took the tire shop an houre and a half to get out to me. He asked where the lug nuts were I said how the hell should I know. An hour later he was back with lug nuts. and a non matching wheel to replace the one that was not usable anymore.

A month later I got a bill from the tire shop for the road service call including the round trip for lug nuts,the lug nuts AND the rusty non matching steel wheel. 

$1350.00 for a guaranteed sounds cheap to me now.

I hope you fought that bill.  Unless this was 100's of miles later there's no excuse for that.  Were these spoke wheels?

With today's brutal roads I think thats the best choice.  As long as its reputable axle surgeon company.  I think most half ass ones I described have faded away.

If that started to fail its not like you'd get much warning.

FYI for anybody here, Frontier truck parts has reconditioned axle housings in the $2500 range I've been using to replace ones with worn out spindles and broken banjos on 404 Eatons, they've been decent.

  • Like 2
Link to comment
Share on other sites

I once had the axle surgeon here, changed a spindle on a 462  (which turns out you're not supposed to)  and he asked if I minded if he took the broken one . Said he could use it cause the threads were good and it didn't have bearing issues.  Must be they do stuff like that.  I have a like new 46,000 pound housing  (seriously, it's not even stained from a carrier) air ride that takes the 6 bolt axles. I'd take a grand for it.

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...