Jump to content

terry

Pedigreed Bulldog
 View Profile  See their activity

  • Posts

    2,381

  • Joined

  • Last visited

  • Days Won

    1

 Content Type 

Everything posted by terry

  1. terry
    Yeah them three straight leaves were pretty soft riding, but leaned real bad. terry
  2. terry
    That would probably be ok for a hobby truck, but one working every day probably not. Terry
  3. terry
    Was this a hendrickson walking beam or a mack beam, and yes mack a solid walking beam years ago. Terry
  4. terry
    Can't you use a filter that came with the tip turbine engines, it has two separate filters in one housing, one for engine and one for the tip turbine.. it is a bigger housing, but it's all on the passenger side. terry
  5. terry
    The biggest problem with a mack single countershaft trans with higher horse engines is do not lug it, keep the rpm’s in higher power band and you’ll be fine, terry
  6. terry
    Just a little warm!😂. Terry
  7. terry
    Original 4:50 rears have been regeared to 5:73 ratio. Terry
  8. terry
    Yeah long as you got one for a pattern shouldn’t be to hard. Terry
  9. terry
    I don't know where your getting the countershaft shims from, i might have some in my shop if you need them. terry
  10. terry
    I’m sure you probably know this, you have to bolt cases together to set endplay on counter shafts and shim accordingly,check at pto opening, and I believe on mainshaft output at back box takes spacers between the two facing bearings to set endplay. Terry
  11. terry
    I once had a vent pipe that had a short rubber piece between valve cover and vent pipe, the rubber collapsed inside and the engine was pushing oil out all over. Terry
  12. terry
    Guess i’m just old school and ran camel backs forever, far as i’m concerned can’t beat them with a very little maintenance. Terry
  13. terry
    What is a twin Y suspension? Terry
  14. terry
    joey are you talking shim paper or shim steel? Terry
  15. terry
    I haven’t heard from him in quite a long time either. He certainly is a ok guy! Terry
  16. terry
    That truck in my profile came from Norm Taunton in Galt, California. Terry B733
  17. terry
    You got your work cut out for you there! Hope the engine is usable. Terry
  18. terry
    Maybe that broaching was a way to cut oil grooves or dimples like original gear bushings on the old 72 series transmissions.🤷‍♀️. Terry
  19. terry
    If you google broaching a gear bushing there are some explanations of it. Terry
  20. terry
    I’m not sure what the broaching procedure is, i think after new bushing is pressed in the broaching tool finishes the inside of the bushing some how. But sounds like freightrain’s procedure should work. Terry
  21. terry
    Haven't seen that done since high school auto mechanics class, along with knurling valve guides. terry
  22. terry
    I know if a gear bushing is replaced they say it has to be broached, don't know exactly how important this is. terry
  23. terry

    Mack R747

    terry replied to 67RModel's topic in Trucks for Sale

    Says C.s. Ehinger, not sure on spelling on the door, they were out of K. C. Terry
  24. terry
    Is the T2100 a ten spd.? The 2070 has a very large overdrive, check overdrive ratios on both, you will probably have to change rear ends with the T2100, the 2070 generally has around 5:50 ratio rears. Terry
  25. terry
    Some six speeds were air operated back box, low, direct, reverse, a 107A, two stick six speed has no air shift controls. Terry

BigMackTrucks.com

BigMackTrucks.com is a support forum for antique, classic and modern Mack Trucks! The forum is owned and maintained by Watt's Truck Center, Inc. an independent, full service Mack dealer. The forums are not affiliated with Mack Trucks, Inc.

Our Vendors and Advertisers

Thank you for your support!

Mack Related Links

Popular links

BMT Forum Logo

HTML tutorial
×
×
  • Create New...