Jump to content

theakerstwo

BMT VIP
 View Profile  See their activity

  • Posts

    3,816

  • Joined

  • Last visited

  • Days Won

    7

 Content Type 

Everything posted by theakerstwo

  1. theakerstwo
    Steam and smoke gets mixed up sometims and steam is coolant in the oil.
  2. theakerstwo
    What trans do you have? I did the same thing but have some heat problems.
  3. theakerstwo
    Some push type clutch did have the counter shaft brake but I think only on the two plate push type.
  4. theakerstwo
    A lot of guys get mixed up trying to adjust the valves on a mack with the dynotard cam.It has a special cut ram on the exhaust lobe that can fool some.
  5. theakerstwo
    From what i understand they grind all of the hard surface off of the lifter and lay a new face back on it.
  6. theakerstwo
    I can not copy and paste here for some reason but search for hillcrest cam grinding in little rock ark.I know some one who uses them and I have installd one cam for a friend from them. They can grind your own and plus reface your lifters.
  7. theakerstwo
    You cant believe ever thing you read on here.
  8. theakerstwo
    And I never did see a 400 manual.And all of my tune up manuals has non listed.
  9. theakerstwo
    The other parts that have a fiber bushing on it is the end off of the aluminum torque arms from the back of a freightliner.
  10. theakerstwo
    If Obama gets hi way all of the coal buckets will be for sale.
  11. theakerstwo
    Ridewell sells kits to use front steer axle.
  12. theakerstwo
    Other dog I set in a truck seat all time. 10 a day in a truck and I have a new truck seat here in my bed room at my desk.Its better that any thing else I could get to go in there.I have a electric air compressor next to it and arm rest on both sides.
  13. theakerstwo
    I saw a R700 one time with a 3208 in it but may have been a implant.That was years ago when the oil field work was still here ever where.This was a rigup truck.
  14. theakerstwo
    Would that be 4 cans or 4 lbs?
  15. theakerstwo
    A injector can cause a miss on one cyl but if it lopes or hunts or as some say jacks it self off then its the governor or a hanging rack.A hunt or lope is when the governor rolls up and down and a miss is something you can hear if you go out there and loosen a injector line.
  16. theakerstwo
    You would want to extend the fuel rack out some so it will have some more fuel.
  17. theakerstwo
    It would have to be a custom built cooler and I have looked into it for a friend.But I think you could do good by using a tip turbin from a 320 or 350 engine which has the water cooler in the box with the air cooler.I would start with calling global truck salavage for the parts.The air to air would have to have the tubes run thru all of the metal work on the front to get to the engine.Some one built one and installed it behind the rad but I think that is no good.
  18. theakerstwo
    Your tires still need to very close in size.
  19. theakerstwo
    You don't have enough info here but if its a older 13 speed like a RTO then its sounds like a broken quill shaft and that's from a bad drive line virbration.
  20. theakerstwo
    That sounds to be in trans but you don't say what trans model. Some more info could help.
  21. theakerstwo
    It has a air cleaner on the rear of the cab up on a rack.Could that be for a unloading blower?
  22. theakerstwo
    I looked at my superliner today and it is like this one here.
  23. theakerstwo
    It would have been a B73 with a long hood.
  24. theakerstwo
    If its a VMAC it will run rough till oil pressure comes up and advances the timing.
  25. theakerstwo
    Your right I learn something new ever day myself.

BigMackTrucks.com

BigMackTrucks.com is a support forum for antique, classic and modern Mack Trucks! The forum is owned and maintained by Watt's Truck Center, Inc. an independent, full service Mack dealer. The forums are not affiliated with Mack Trucks, Inc.

Our Vendors and Advertisers

Thank you for your support!

Mack Related Links

Popular links

BMT Forum Logo

HTML tutorial
×
×
  • Create New...