Jump to content

terry

Pedigreed Bulldog
 View Profile  See their activity

  • Posts

    2,210

  • Joined

  • Last visited

  • Days Won

    1

 Content Type 

Everything posted by terry

  1. terry
    Don't know the model no. but some B models did come with a chrysler motor from the factory. terry Think i got the 413 in a B mixed up with the early R models !
  2. terry
    I have seen a 38 and a 44 housings on the same tandem before. terry
  3. terry
    34k and 38k rears main difference is number and thickness of the spring leaves, And spring pads and caps. 34k,38kand 44k diffs are all the same. terry
  4. terry
    How did they ever get a cat motor in a B61 ? terry
  5. terry
    Nice looking rig !
  6. terry
    To get 72 with a 9.10 ratio you must be doing some serious overwinding the engine ! terry
  7. terry
    Look forward to them winfall wimmin ! terry
  8. terry
    Then you will need a 3.86 or a 3.65 set of rears. terry
  9. terry
    Next faster would be a 3.86 might be hard to find, I would go with a 12 spd. overdrive T1070 trans, with 4.17 rears you will turn about 1750 rpm at 70 mph. terry
  10. terry
    Kingpin on the side with tire worn more on the inside?
  11. terry
    I wasn't telling which way to go on the seals, most people don't there are two seals till they get them apart. terry
  12. terry
    A lot of people don't realize some of the old macks had two wheel seals on each wheel, hand packed in bearing grease for the inner bearing, and the the outer run in gear oil. With a seal between them, most people would remove the outer seal and run both bearings in oil. Don't know if it takes a different inner seal then. terry
  13. terry
    As you look at the front of carrier there is a flat spot to left of input shaft, wire brush this area should be a set of numbers of ratio. terry
  14. terry
    No problems don't you give it a second thought. Already forgotten. terry
  15. terry
    Whats the specs and is it a runner? terry
  16. terry
    Check your posts again, you asked who weldons was and I answered. Different poster is looking for the parts. terry
  17. terry
    I'm not looking for the parts, just answered who Weldons were. terry
  18. terry
    Extended service interval I believe. terry
  19. terry
    Weldons is a truck parts co. our local one stocks all brake and air parts and front end parts. terry
  20. terry
    A 44.000 camelback is going to be ALOT rougher ride than that taperleaf. terry
  21. terry
    Is the truck a work or play truck? I have seen alot of trunnions welded or plated to repair them.
  22. terry
    If you look at the rear suspension it is a real old set up, the inverted camelback not used since about 1970. Also not a 38.000 rear ,but a 34.000
  23. terry
    Makes mine look like a pigpen! terry
  24. terry
    I would bet the drag links are the same, unless one had a really bigger axle. You would never use them 7.00 ratio rears terry
  25. terry
    Definitly a DM frame, must be a pretty early engine or whole running gear, has the old belt driven power steering pump. terry

BigMackTrucks.com

BigMackTrucks.com is a support forum for antique, classic and modern Mack Trucks! The forum is owned and maintained by Watt's Truck Center, Inc. an independent, full service Mack dealer. The forums are not affiliated with Mack Trucks, Inc.

Our Vendors and Advertisers

Thank you for your support!

Mack Related Links

Popular links

BMT Forum Logo

HTML tutorial
×
×
  • Create New...