Joey Mack
-
Posts
7,605 -
Joined
-
Last visited
-
Days Won
197
Content Type
Profiles
Forums
Gallery
Events
Blogs
BMT Wiki
Collections
Store
Everything posted by Joey Mack
-
I would think that if the trailer button is installed, then the system is there.. My guess, is that he needs help with basic's. I would like it if he raised the body and took pictures of the air plumbing, and also of the rear plate.. Like you said Mech, there may be capped lines..
-
89 Super liner Fuel sending unit
Joey Mack replied to tegra1027's topic in Electrical, Electronics and Lighting
The wire that is attached to the tank is to be hooked to the original return wire. The tank is not a good ground due to the rubber strap insulators. The end with the butt connector goes to the original power wire..or signal 'in'.. touch the new wires to the old wires and look at the gauge. If it pegs to full, swap them. -
Well,, I am trying to remember the oldest automatic truck that I've seen.. old firetruck I guess... I'm thinking about buying a new camera.. but I is Po..
-
Solar no, RD Yes
Joey Mack replied to masterwelder's topic in Antique and Classic Mack Trucks General Discussion
No corrections needed.. -
Me too, Joe..
-
Not impressed..
-
It pisses me off that Donald Trump has had to pay many millions of dollars in court fee's and other junk, and is not even convicted of a crime, and 2 big players in this B.S. would cry 'Racism' in a heartbeat if the tables were turned.. In other news,,, my health insurance is going up by 3-4 %, not a big jump for me, but a jump non-the-less... I wonder if the illegals and the welfare peoples health ins. went up too?? Gotta laugh, or else I will go nuts... Jojo
-
E6-285 2VH problems and solutions
Joey Mack replied to allfritz123's topic in Engine and Transmission
Is the throttle arm pulling all the way open when you push the throttle. -
FJH, did say something that I have had to fix before.. I had to go behind the first guy, because he didn't use any rubber bands to hold the little plungers up inside the rockers and got a few of them side loaded. I had to replace the rockers because there was a groove inside the bore from the crooked plunger..
-
2003 MR688S rollover cab swap
Joey Mack replied to JoeH's topic in Modern Mack Truck General Discussion
whoever gets to drive this one, had better be greatful.. The work that you guys are doing is really nice, and you didn't give up on the wrecked older truck.. Awesome... Jojo -
Me Too... Snowdog
-
Yes #2, I don't have specs.. the EUP may not be the issue.
-
Ok.. check the wires for the EUP's they are known to rub against the engine block and short out. Be very careful with the 5mm screws. They do NOT come out. Just loosen them and slide the terminal back and up and out. I recommend taking all 6 sets loose and stretch the harness out.. it seems like it's an 8-2 code. The second number represents the EUP #
-
What year and body is the truck
-
Need to send them to the states.. ours are junk..
-
I am really glad that you posted the fix and a picture.. Too many guys throw money and parts at the issue, when in many cases its a wire.. I preach this 90% of the time. well really 100%, but you get my drift.. You are proof to the next guy that you need to diagnose the issue, not try to buy the repair.. Jojo
-
yep. its plastic and has quick connects.. great for the assembly line, totaly sucks for the owner/mechanic
-
DD's?? Hell, I didnt see my wife in the pic's. I guess I need to look again..
-
that air manifold is a common problem. its all quick connects, and they spring leaks. some of those are straight through, but when you look close you will see galleries connecting the ports.. so drilling out the leaker and installing a small union, may not work.. it will cause other issues. if you have enough line to trim 1/2'' off and re-insert it, you can try that, but we just replaced the whole manifold.. you will have to work on both sides of the firewall.. I suggest you stock up on 'curse words'. youll need 'em....
-
He will be Jewish next November and December..
-
Connecticut Construction Trucks
Joey Mack replied to BKrois's topic in Antique and Classic Mack Trucks General Discussion
Its sad.. here in Charlotte, the crimes of car theft and vandalism and shootings, really all crimes,, is starting at the age of 12, and many are between 14 and 17 years old.. This is what happens when a man makes a baby but doesnt be a Dad to that baby. -
info?? did you use the magic wand to scroll through the codes? the odometer kind'a scared me a bit.. š
-
remove coolant fan on 2007 cv713
Joey Mack replied to Mack Hammer's topic in Modern Mack Truck General Discussion
good deal, yes it could be more ''mechanic'' friendly.. glad you got it out with out damage, I forgot about the A/C lines.. -
remove coolant fan on 2007 cv713
Joey Mack replied to Mack Hammer's topic in Modern Mack Truck General Discussion
Hey Mack Hamer??? can you post some pics from both sides, not close ups? I get mad at myself when I cant answer a question like yours because I know these trucks, but I am rusty on the fine details for some reason.. -
Macks... did you take a minute to roll through the 124 pages?
BMT Forum Logo
