fjh

Yup I would have thought you would have had more poor starting symptoms with a pump that bad! the loosing prime thing happens more often than a low power complaint! We had the loss of prime thing happen the last week ! We checked ALL the normal things with no luck pressure was ok but fluctuating some so we changed out the pump! Once the pump changed ,ALSO no luck we were stumped ! The truck would run after cranking for ever to get it to start If u turned it off it would not start a minute later! reminded me of an MP engine with bad cups ! So I checked The fuel return fuel was full of bubbles just foam The whole time since these engines have been around I have NEVER seen this! So rolled the dice and pull the injectors had em tested! 4 would Not pop test AT ALL the guys gauge maxed out the other 2 were just slobbering fuel it was amazing the engine ran at all ! funny thing is it really didn't sound bad ! Anyway just another Shit happens occurrence Kind like your fuel pump ! Again Good find on the pump Red !

Its to bad the wheel had to squeak so long to get greased , how ever at least it got some! Good luck with the new unit when it gets here bro!

f**ksakes What a pain! So much for the flat rate hope you get paid by the hour!🙄

Another bandaid! They now lock tight and stake the nut horse is out of the barn though! Day late two dollars short!

Sorry to say but in my mind right now you got mostly a big red boat anchor under your hood from what you have said! it may not be worth repairing this ! Due to the age of the unit!

Unfortunately the dude who put the compressor on blew it big time when you got broken gears you need to go looking for why they broke! And these engines have a track record!

Yup and it was still running that’s the bad part for you yours is not 30 grand could go away in a hurry!

We just finished one in the shop roughly fifty hours into it tandem tandem mixer plus 10 grand in parts not a nice situation!

you can safely fill the primary filter!

This statement could not be more true in my mind ! That being said.Volvo should now have the best of both worlds ! Over priced parts and a piece of junk to keep putting them on ! However! Don't think for one minute Paccar and the freightsaker /westernstar IHC makers Aren't Doing the same dam thing Its rampant thru out industry as a whole our economy relies on repeat business and waste ! So build a piece of junk , sell it and they will come back One way or the other they sell parts OR sell a new unit in 5 years or so Because the consumer gets tired of being in the shop having parts thrown at the stuff they bought! All in the Plan! Again its a no win for us the consumer, A semi win for them and a total loss to the environment because of all the waste! It does keep people employed I guess!😥

Also seen this happen this gets you possibly happy and they can sell this truck to someone that don't know any better! what ever works I guess! Usually comes with a keep you mouth shut stipulation I think!!🤔 The Mp8 is a some what better design in my mind however Don't expect good mileage with an allison! we have quite a few running here and are trouble free for the most part!Allison is a better choice for a dump configuration And almost any niny can drive it with out wrecking things! Leaves you open to letting your wife or girlfreind driving it for you while you sit home drinking beer! 😉

Exactly my thoughts!

To bad they hadn't stole the syncro design as well ! How ever problems seem to be less prevalent on these its still there!

If you ever had long distances of backing up to do you mack 12sp would run circles around the fuller or Mack 18 sp and get twice the work done in a day! Its a shame they discontinued it ! Dispite its sometimes ornery last gear split it was a good trany for many vocational job Applications !

Another issue with the cylinder is there is a snap ring that can break inside the cylinder and cause this symptom you can do the oring job with out removing the lid from the back of the trans with the exception of the rail oring pay attention to the assembly as it is easy to get your head messed around to the way things are assembled!at least for me! :)Remove the four 3/8 by 4 bolts and remove things in order the end cap first the outside barrel being second then the outer piston theres two as you can see by Robs post!An inner and an outer! install the new orings on the pistons and if the snapring is broke replace it and reassemble!

Brain fart on my part sorry ! You are correct of course the will not work

AI use my thumb loosen the jam nut turn the adjuster in till it won’t move the with a screw driver or your thumb back it out one half turn then place your blade under the rocker turn the adjuster in till you got drag on the feeler then lock it with your 11/8 wrench and check the feel it can change as you tighten the jam nut! Adjust as nessary to get the right drag on the blade

Same set as an late 80s e 9 with a v fuel pump 16 inlet and 24 exhaust set in firing order

So what became of the RAPTOR version of these? Speaking of Hype!

Check pai good pricing! 57GC197A

Their are two one on the manifold end one at the compressor!

Check the little hose at the compressor inlet and under the inlet manifold! those often burst! its a one inch steel line that runs behind the engine

The idea here is to expand the aluminum from around the nut yuo are replacing the valve

Cheap cheap cheap thru out the industry it seems very sad!wonder what would happen if say autocar or someone started building a good quality unit say ten grand more would people buy?Or is price the selling point here!

Ahhh! another step backward for a reason thou ! Well that"s a breath of fresh air! I thought they were being illogical for no good reason! But there is a reason for being illogical ! Thankfully We haven't had the displeasure of working on the ( new power assist ) option yet ! Were still working patching up the other issues that haven"t been addressed 😡! Rear Engine mounts have become an issue as of late ! Thankfully we have the odd bull gear failing still , on the older trucks so the mounts can be addressed at that point🙄!Planed obsolescence! have said it before , Its a shame these Volvo people bought a company that had some well established people and ideas that worked ! And they never ran with any of it! Having said that the front bumper on the new Anthem s we've been selling here have a bumper 1/4 that can be removed for better access for service and repair !😁 Its horrible to work on. With an inch or two of clearance. No changes needed to be made to the Volvo to fit that God awful design hanging off of the D13/MP8. Well they made it easier to get at the EGR valve at least What more to ask for! 🙄