880joe
-
Posts
500 -
Joined
-
Last visited
-
Days Won
1
Content Type
Profiles
Forums
Gallery
Events
Blogs
BMT Wiki
Collections
Store
Everything posted by 880joe
-
That fixed it Mackpro thank you very much
-
my selinoid only has one port on the side air from truck and one out of the bottom to the fan and exhaust port on the top
-
Yes I already had air fan just took off a kysor and replaced with a Horton
-
Any chance it would need changed in the ecm I tried just switching air lines on selinoid that doesn't seem like it works. Just a single air line surly not to many ways to plumb
-
How do I need to plumb it
-
is a kysor and horton fan clutch opposite as far as one taking air to engage and the other requiring air to disengage
-
The 08 and newer would be a real pita looks to me like. They moved ac and heater core to right side of cab and the wiring and air lines going into cab looks alot different
-
I can not see any difference in the cabs there maybe some minor things but should'nt be to hard to overcome them
-
Is the cat cross member different from an e6 or e9
-
I would'nt know why you could'nt put up to an 07 model cab on your truck as long as it had the etech engine and not the mp series engine. I have an 07 and some 99's wiring looks like same plug in on firewall but the 07 does have 9 pin data port under dash and 99 only has 6 or 7 pin plug in. TimberJack said in his post there was 2 extra wires
-
Did you change front engine cover so that the ac compressor was on the left side And did you have to change anything else
-
I have not run the Rochester injectors long enough to know how reliable they are going to be. I ran the K&S 100hp injectors and did have a few of them split the tips. the Rochester 2.5 are supposed to be a little bigger but they claim they do their injectors different some how and don't have that issue guess time will tell. I never had any problems from the 75hp injectors from K&S they have been the most reliable ones and cheapest that I have used so far only been using Rochester for about a month now.
-
I'm thinking 525 or 550hp probably need a little more turbo to cleen up the smoke and get a little more power
-
I changed the eup's because I had put some used 1's in in the past and never had the cal code done on them and some were leaking a little fuel also had 2 or 3 people tell me they got week over time mine probaly had a million plus miles. I belive I sent my old 100hp injectors from K&S to Rochester for cores and they compaired to there's and said 2.5 were just a little bigger and the stage 3s you would need to watch your egt's and water temp
-
I bought the new eup's off eBay for 200 each Rochester injectors will run you about 150 each K+S injectors are 85 a piece
-
Want to build a competition pulling truck
880joe replied to tree98's topic in Engine and Transmission
Brutus if you do the upgrade you suggested what kind of power will you be getting. Also what is the best suspension to run on stock class puller -
I ran the 75hp injectors from K+S for 4 years without any issues. About a month ago I put Rochester's stage 2.5 injectors in and new eups my driver said he about had to learn to drive it again it made a big difference. I'm driving a 355/380 with injectors from Antrim Diesel and 460 turbo I will loose 18 to 20 mph on the same hill my driver said he looses 2 mph
-
KandS diesel out of Schofield WI or Rochester Diesel out of Rochester MN both have better injectors that will get you more power
-
will a rear mounted pto off a 12speed fit a 2 stick 6 speed
-
A t800 kw I wouldn't consider a classic truck with its sba and sloped nose.
-
1998 Mack rd 688s etech 350 won't start
880joe replied to Lucky dogg's topic in Engine and Transmission
I may be the gear slipping on the fuel pump -
I only had the taper leaf on a couple of road trucks they seemed to ride pretty good and had good articulation in the truck stop parking lot pot holes. The ride is much better than the camel backs that I have had.
-
CH613SBA hood fit a CXU613?
880joe replied to Rockwell's topic in Modern Mack Truck General Discussion
I think the hood would fit but the bumper probably won't because I believe the frame is wider on the CXU than the CH so your tow hook holes won't be right. -
I have st34 suspension I believe. I got ahold of Donovan Spring and pretty sure they have what I need. Thanks for the response and help
-
Does anybody make a 44000lb replacement spring for taper leaf spring suspension. I was told that there was an aftermarket one available but haven't been able to find any
BMT Forum Logo
