Jump to content

Mark T

BMT VIP
 View Profile  See their activity

  • Posts

    1,617

  • Joined

  • Last visited

  • Days Won

    12

 Content Type 

Everything posted by Mark T

  1. Mark T
    Flanked by a couple Autocars no less. All Pennsylvania's finest.
  2. Mark T
    Volvo is developing engines as well. High tech..... but still Diesel fired.
  3. Mark T
    That truck needs nothing , other than that guy keep using it. 😉
  4. Mark T
    We still luv ya
  5. Mark T
    That was pretty fast. Guy didn't fool around .
  6. Mark T
    I'm like'n the 1150 TC. They were quite the piece of equipment for their time. Rare sight here now.
  7. Mark T
    I believe that arrangement is called "modular" (that valve that you just keep adding to for more components to control withone air source) 👨‍🎓
  8. Mark T
    Is that the new hood ornament they'll be using on the macks made in Mexico ? Or will they be modeled after a chihuahua ?
  9. Mark T
    Why would Mack or Volvo ever put a big engine in a truck again ? The MP10 or D16 did miserably as far as sales went. Most vocational trucks don't need them and most VNLs ??? the guy with the ear buds and crocks.... he couldn't care less. Then factor in the handful of guys that think they need a 600, and have no idea how to actually use something like that, He'll be back crying for warranty on stuff that isn't covered. Caterpillar saw it coming, now Volvo does too.
  10. Mark T
    Safe bet you'll never see a big bore engine in a Mack ever again.
  11. Mark T
    They can check all they want Bob, when they have only a small idea what they're looking at there's not much chance to get it fixed. Now if it was some mindless thing on tick tok or something you needed fixed.... you'd be all set. But hey !!!! they showed up that day 🤣
  12. Mark T
    Be a nice tractor for a dump trailer in New York with a 117000 pound permit. 😏 take those gay mufflers off and let that puppy bark.
  13. Mark T
    That's about all the information that's in the Chilton book. The book isn't specific to the truck, it covers several. But if you think it'd be of any help, I'd ship it to you.
  14. Mark T
    Most of the upgrades require 12 volts to the distributor . IDK if the truck uses a balast resistor (or wire) , but I know most need 12 volts . The Petronix distributors are emphatic about that when you buy the whole distributor I know.
  15. Mark T
    Not much different than 4.64s. Still a 70+MPH truck.
  16. Mark T
    You would look good in that one.
  17. Mark T
    Carb kits are on Ebay. If that's a two barrel it's likely a 852FFG. I have an old Chiltons book Iv'e been looking at here. That truck reminds me so much of my uncle's dump truck when I was little. Hit a soft spot or something.
  18. Mark T
    That big gas engine likely has the same carburator base as a Holley 4150. I think that one easy plug n play one is a (Sniper) ? Get some clean gas to the engine , I think I'd be more worried about heat'n up the ignition some way. I'd imagine someone makes something that can make it transistorized instead of points. A nice hot high energy ignition will be harder than a good rebuild on a old Holley. ( I'm assuming it has some form of Holley on it). 401 might only be a 2 barrel . Either way, a kit probably is available .
  19. Mark T
    Have you seen inside a carburetor after sitting with ethanol gas
  20. Mark T
    Truck sounds great, and a good reason is you certainly seem to be pretty good at shifting it. Even if you were a driver with lots of experience, you got pretty good at it concidering how long it's actually been running since the restoration.
  21. Mark T
    Looks like all you can do now is swap out that IH engine for a 5.9 . Or...... stick to non ethanol . That stuff works if you used something frequently, but leave it sit a little and the fun starts. I think I'd leave the tank as full as posible for the periods it sits. You'd think these guys repop'n tanks would realize this and make a composit lined tank even if only for novelty trucks. At the point of manufacture, it wouldn't be very difficult to line it with a poly membrane or something.
  22. Mark T
    I beez tink'n daht eez him mohn. Kid does better than most 4 times his age around here at this point.
  23. Mark T
    Exactly. No need for that pesky after treatment. If it moves ??? just get in and start power shift'n (lol)
  24. Mark T
    Joey ???? are you saying that a trailer there wouldn't be like one here ? (lol) In so many ways, they're 75 years behind . I wonder how the after treatment works on that truck.
  25. Mark T
    I think I might have seen his nephew or something by Port Newark

BigMackTrucks.com

BigMackTrucks.com is a support forum for antique, classic and modern Mack Trucks! The forum is owned and maintained by Watt's Truck Center, Inc. an independent, full service Mack dealer. The forums are not affiliated with Mack Trucks, Inc.

Our Vendors and Advertisers

Thank you for your support!

Mack Related Links

Popular links

BMT Forum Logo

HTML tutorial
×
×
  • Create New...