-
Posts
2,185 -
Joined
-
Last visited
-
Days Won
29
Content Type
Profiles
Forums
Gallery
Events
Blogs
BMT Wiki
Collections
Store
Posts posted by h67st
-
-
- Popular Post
- Popular Post
-
Swish, you are truly a master of computer graphics. If the trucking thing doesn't pan out, you could always make a living doing the graphics.
-
Will it turn the right direction for down under? 😉
- 1
-
Can you get a picture of the right side latch? I've got a latch that fits L models and H models, I just wonder if it fits yours.
-
If it's the lighter, non-metallic green it's Mack paint code 808 Light Mint Green. If it's the metallic like B models then it's Axalta 44419 Frost Green Metallic.
-
Back in the 70's when "Convoy" came out I must have run the needle thru more than one copy of it! A real talented guy.
-
- Popular Post
I got the heater all assembled with new blower motors; the heater motor is CW and the Red Dot catalog showed they had one, turned out their catalog was wrong so I went to Unimotor (Four Seasons) and you can get the correct motor from RockAuto. I'm not happy with the front cover but thankfully I have a better one I can clean up and paint to replace it with.
I took the shifter boot frame to an upholstery shop in Columbus and they made me a new boot out of vinyl.
The original setup was anchored to the shift levers and caught on some spring catches in the cab. I drilled four holes in the boot frame and cab so I could bolt it in place. I had them put zippers at the top so when I raise the cab I unzip each one to allow the levers to slide out of the boot.
- 8
- 2
-
Asking $750 plus shipping or best offer.
https://www.ebay.com/itm/154922812972?hash=item24121e862c:g:O3UAAOSwE6FiQ0CF&autorefresh=true
- 1
-
-
I used Axalta 44419 Frost Green Metallic, it's an excellent match for original.
-
Nice truck on ATHS back lot. $28,000 for the tractor and $17,000 for the trailer.
https://aths.org/backlot/135834/1963-mack-and-1950-trailmobile-trailer/illinois/usa/multiple-makes/
- 2
-
- Popular Post
I bought some of the split loom to put the wires in, I used 3/4" for the big bundle which is easy to work with. I got 3/8" for the small bundles which is not easy to open up for someone with 58 year old fingers. I should have checked to see if they sell a tool for "unzipping" the loom to insert the wires. I used all black wire because I didn't want to buy a dozen rolls of different colored wire.
I got everything wired up and so far it all works. I had a Mack speedo and fuel gauge, but haven't been able to find any other Mack gauges so I had to go with Stewart-Warner.
Saturday we had nice warm weather so I cleaned up some parts and painted them outside.
- 9
- 2
-
If you ask dumb questions, you'll fit right in here!!
- 1
- 1
-
It's great to hear about someone helpful like that. Nice road boss...290 Cummins?
-
When I worked at Cat we had a "start cart" which was 4 batteries with heavy jumper cables and you could select 6, 12, or 24 volts. When it was cold outside and a 12v truck was turning over lazy, switching to 24v would really get it spinning!
- 2
-
- Popular Post
- Popular Post
14 hours ago, tjc transport said:you actually understood that??? 😲
I did right up until he mentioned the flux capacitor.
- 1
- 2
-
Well, I tried to sell this wheel on ebay, no takers. I think it's off a 50s or 60s GM truck; it's got the 11/16" shaft. It's 20" diameter, and the hub has the numbers 65 435 on it, made by Sheller. It's got one crack, and it looks like the discoloration will polish off of it. If anybody wants it you can have it, just pay for shipping. PM me if interested.
-
4 hours ago, mowerman said:
Faulty parallel switch????! Sounds like an easy fix with a test light good luck.. Bob
I'm with Bob on that...if it's got a S/P switch, could be the problem.
-
Well, the steering wheel I bought on ebay won't fit my truck. Mine has a 1-1/16" spline OD and this wheel has a 15/16" spline. It's a 22" wheel, from a later truck-60's? 70's? I paid $175 for it so if anyone wants to buy it I will sell it for that much plus shipping. It's got some small nicks and scratches, and the center hub has a little damage on it but there are no cracks anywhere. PM me if you're interested.
-
17 hours ago, mowerman said:
Not sure if I missed something did you get the R model steering wheel and does it fit bob
It's supposed to be on the way, I haven't seen it yet. You know how those FedEx guys are. 😉
-
- Popular Post
-
13:00x24s...sounds like some beastly tires!!
- 1
-
13 hours ago, Mean Green said:
found this pittsburgh craigslist
$100 is a good price, unfortunately it's a 20" wheel. I bought a 22" one on fleabay out of an R model, I haven't gotten it yet. Hopefully it will fit.
-
On 1/23/2022 at 10:43 AM, mowerman said:
you know years ago i hadda 51 chevy pickup and i took a steering wheel out of a 52 pontiac because i did like the the one the truck came with,,,cool dashboard but ugly wheel it fit right on....so we know thier is alotta interchangable available....sick thing is we know there is got to be alot of brand new steering wheels out there,sitting in boxes in old wharehouses somewhere with all that hard work you have done,,,must be driving you crazy to hit a brick wall here...bob
I read online that a lot of the older GM cars/trucks used that 11/16"-36 shaft.
Gold Dogs
in Antique and Classic Mack Trucks General Discussion
Posted
These are the only ones the guy had, he used to work at Macungie and had kept these around for many years. I'll ask him if he knows what they used them on.