Jump to content

880joe

Pedigreed Bulldog
 View Profile  See their activity

  • Posts

    548

  • Joined

  • Last visited

  • Days Won

    1

 Content Type 

Everything posted by 880joe

  1. 880joe
    Where is the tractor protection valve at on a 99 CH mack?
  2. 880joe
    I believe you are going to need to stay with the AC engine or have to do a lot of modifications to make something else work. What is wrong with the engine you now have?
  3. 880joe

    12 speed pto

    880joe replied to Steve L's topic in Parts Wanted

    Guess I lost your email address could you pm me again with it I took some photos today
  4. 880joe

    12 speed pto

    880joe replied to Steve L's topic in Parts Wanted

    Yes I got it I've just not had time to get pictures
  5. 880joe
    I believe the 6-4 code means the ecm is not communicating with the vecm
  6. 880joe
    I just had to replace the engine ecm on my 99 CH if I remember correctly it gave a 6-4 code. It acted up 1 day then ran fine for a week or so then went to leave 1 day it started and died immediately then never ran until I changed ecm.
  7. 880joe
    A friend of mine tried replacing an 07 AC engine with an 01 etech and never could get it to run said wiring was totally different and a nightmare don't know you would run into on an AI
  8. 880joe

    12 speed pto

    880joe replied to Steve L's topic in Parts Wanted

    I have got 1 on a transmission I believe it has 1 ear broken off where it bolts to the transmission and leaks a little grease out but don't think it affects the operation of it any
  9. 880joe
    If it's a mack rearend it may be the peanut cluster wore out and slipping
  10. 880joe
    Joey Mack is from somewhere in North Carolina
  11. 880joe
    Yes they will fit but the door stopper that keeps door from opening to far is different
  12. 880joe
    4 valve engines had both style of pumps
  13. 880joe
    I've been told you could use spring loaded ones and have an engine with steel rollers and spring loaded push rods acording to my mechanics. But that engine also didn't sound right through the intake and nobody could figure out why
  14. 880joe
    So can you use the spring loaded pushrods with the steel rollers?
  15. 880joe
    I had ceramic lifter fail and mack dealer wouldn't put steel lifter back in
  16. 880joe
    Have you tried just leaving it a little low and see if it quits pushing coolant out? Also what dealers are you dealing with so the rest of us know to stay away from
  17. 880joe
    I would possibly be interested in the whole truck
  18. 880joe
    How much for the etech?
  19. 880joe
    So being a guy on the mack site an describing the t800 cab and ride the way you did how do you feel about the R model mack cab and ride? I never drove a t800 but the R model macks that I drove wasn't alot of room and sure didn't ride like no Cadillac
  20. 880joe
    You're going to spend alot of money changing cam gear for a little bit of hp just my opinion. If it were me I would put the 355/380 program in it and leave cam alone a whole lot cheaper and same amount of torque
  21. 880joe
    I'm surprised that mack dealer would put the 427 file in without changing cam. I tried having a 460 turned down to 355/380 and they wouldn't do it without changing turbo,injectors and cam. He must have a better dealer. Also I thought I read if you didn't change cam key it get hot if you didn't watch it close
  22. 880joe
    A pre CCRS engine would need the cam key changed
  23. 880joe
    Might also check for loose wheel bearing
  24. 880joe
    I believe this was discussed on here before and was said you can get that hose from PAI
  25. 880joe
    Kt engineer do you work at the factory for mack

BigMackTrucks.com

BigMackTrucks.com is a support forum for antique, classic and modern Mack Trucks! The forum is owned and maintained by Watt's Truck Center, Inc. an independent, full service Mack dealer. The forums are not affiliated with Mack Trucks, Inc.

Our Vendors and Advertisers

Thank you for your support!

Mack Related Links

Popular links

BMT Forum Logo

HTML tutorial
×
×
  • Create New...