Jump to content

MACKS

Pedigreed Bulldog
 View Profile  See their activity

  • Posts

    1,617

  • Joined

  • Last visited

 Content Type 

Everything posted by MACKS

  1. MACKS
    Adjust in firing order on tdc compression stroke.
  2. MACKS
    Forget about the oven and get one of these smokers,only about 60 bucks at home dopey or blows...
  3. MACKS
    6.34 would be slow even with an overdrive trans,someone on here might be able to figure it out for you.
  4. MACKS
    Are you living in the stone age,as a hunter I have seen many wabbits infected with parasites,the most common being tape worms,so if Buster eats bunny with tape worm then Buster gets tape worm,Not Good...
  5. MACKS
    Raw bunny's are not good for Dozer,they need to be cooked first if possible...
  6. MACKS
    I only mounted one on an RD and I used self tapping sheet metal screws with an ample amount of silicone to keep out any rain water...
  7. MACKS
    We used to run trucks with farm plates on them,no nys insp was required but the truck had to run on a designated route,that was many years back so might be different now...
  8. MACKS
    It is a bolt and when you remove it and the washer behind it the slack adj should slide off,to replace the bushings you will have to take the s cam out and to do that you have to remove the drums,I would leave the bushings till you replace the brake shoes..
  9. MACKS
    I believe he's talking about 2010 year,is that right?
  10. MACKS
    Guess it's good thing I cant afford a new Mack,but never had any issues with the older ones,work them hard day after day on and off road,routine maintenance is all they needed.
  11. MACKS
    I think it's safe to say that you better have good brakes and have them adjusted properly and have good tires and tight steering and no broken springs or cracked windshield ect,ect,ect,or you will be put out of service just like any one else,antique or not...
  12. MACKS
    Got stopped in my 83 RD once and just in case I laid the belt across my lap,dam trooper came right to the driver door opened it and pulled on the belt,well the buckle dammed near hit him the head,lol,needles to say I got a ticket...
  13. MACKS
    Got stopped the other day by Suffolk County Motor Carrier,he didn't even ask for my license,just wanted to see my ow permit,took the permit walked around the truck looking at everything than gave it back to me and said have a nice day,also said I was the first truck he stopped that day that had an over weight permit,it's all about the money there looking for the big money tickets around here.
  14. MACKS
    A friend of mine has an 86 RD 58 rears with the original bronze bushings still in the truck,he did replace the rubber pads once or twice,this on a very well used truck,just saying..
  15. MACKS
    Hay Sean,how ya doing,I was told a long time ago a diesel truck engine should run 100 degrees above the outside air temp,check the gasket on your air box.spray some starting fluid around it while it's idling,stay cool out there...
  16. MACKS
    Agree one hundred percent,that would put 90 percent of the lawyers on the unemployment line but save the courts and taxpayer a small fortune...
  17. MACKS
    There's ten teaspoons of sugar in a twelve oz coke,her blood sugar level must have been off the charts!!
  18. MACKS
    Here's a shot o mine..
  19. MACKS
    Kinda hard for me to explain but you need to measure just the flat part of the rim,get the end of your ruler right in the crevasse on the bottom of where the rim slops up,where the chocks go and measure to the outside of the rim.does this make any sense?
  20. MACKS
    Smithtown is a large town ,I've been in there highway yards a few times,they have lots of heavy equipment including many 10 wheel dumps,they used to have all auto cars before switching to Macks.
  21. MACKS
    A good spring shop should be able to replace the entire rear suspension for about six thousand,maybe a little more if the saddles are shot,that's with new springs to.
  22. MACKS
    The mounts in the picture are the same ones I had on my 83 RD but there was no threaded rod,what do the mounts look like on your truck now,if there the same as the picture I would leave them.
  23. MACKS
    I did find two but there shot.
  24. MACKS
    I find it hard to belive the members support this..
  25. MACKS
    Barry should be able to answer that question,shoot him a PM.

BigMackTrucks.com

BigMackTrucks.com is a support forum for antique, classic and modern Mack Trucks! The forum is owned and maintained by Watt's Truck Center, Inc. an independent, full service Mack dealer. The forums are not affiliated with Mack Trucks, Inc.

Our Vendors and Advertisers

Thank you for your support!

Mack Related Links

Popular links

BMT Forum Logo

HTML tutorial
×
×
  • Create New...