Joey Mack
-
Posts
10,669 -
Joined
-
Last visited
-
Days Won
235
Content Type
Profiles
Forums
Gallery
Events
Blogs
BMT Wiki
Collections
Store
Everything posted by Joey Mack
-
Buddy,, I know what you mean.. I'm glad you were looking up ahead, and all around you... unlike 1/2 the drivers of today. I have considered selling my Softail Duece, because of this issue.. Last Saturday my wife and I put 170 miles on her Tri-Glide. I don't ride anywhere near as much as I used too. I was very aware of my surroundings..
-
Yes sir...
-
It's gonna look like there's no way to remove the transmissions with the rods connected, but it WILL come out and go back in. You need to remove the plastic valance panel under the windshield. Remove the wiper motor to get to the crank bolt.. do you know how to set the wipers correctly and then hook to the motor? It's not rocket surgery.
-
??
-
I say YES !!!!
-
I really wish I knew why the pictures would post in the " Batman Mode''... I'm sorry.. i guess you can tilt the laptop to read it..
-
I hope these pictures help you.. You can check the wires for shorts and damage.. Do you know how to read the wire codes?
-
Well. I just got " out bid" on this one. Oh well.. -
1995 mack ch t2180b transmission
Joey Mack replied to Playinghooky13's topic in Engine and Transmission
Is it the same length as the 2180? If not, a drive shaft will need to be made.. -
And it's furnished with the " early American yard sale" motiff...
-
8-9 is related to all of them.. don't buy any pumps yet, check the condition of the wire harness.. I Believe the ECM has only 2 plugs. I know I posted the pin out diagram for them on other threads. And a couple others have too. I think pin 11 + 12 in the J-2 connector are the comm lines. 1-3 are on one line and 4-6 is on the other. To me, this is likely a wiring issue and not an EUP issue.. due to the 8-9 code... Jojo
-
It would cool to win the bid. I figure I could try to fix it up for someone wanting a 2 valve...
-
I have a trailer...
-
i will keep y'all posted i'm workin on it..
-
Brocky,,, I set it up and I have the highest bid at this time... now.... how to get it to my house if I win.. I did get a message from one of our Brothers, offering to help me.. 👍
-
B-73 Restoration
Joey Mack replied to mattb73lt's topic in Antique and Classic Mack Trucks General Discussion
Shute Boom's are awesome !!!! -
Well, if it is the issue, and you post the repair, I bet I learn something.. Have you pulled the cluster to see if the wires are connected good?
-
Well that would be great... I guess I need to try to place a bid.. Thank you.
-
673.. sounds great. Im not done blasting parts yet. I forgot, I need fuel lines too.. I will keep in touch . Jojo
-
2 valve rocker shafts assemblies, pushrods, and water manifolds to start with... i have one in my shop for about 3 years now. I'm moving slow..
-
Yo..!!! I would pay $500.00 if I had a cheap way to get it home
-
I love mine !!
-
Speedometer drops off while driving
Joey Mack replied to jcutler's topic in Electrical, Electronics and Lighting
Let me guess... an MP-7 with an Eaton tranny? Have you looked at the wire harness for the speed sensor and tranny for cut or chaffed wires..? You seem to have put a good bit of parts on it with no repair.. I would say a bad ground or short to ground in the wires is the issue.. Peel back the loom and check.. Just sayin'... -
i would pay $500.00,, but I live to far away... oh well.. I need the parts for the one in my shop..
BMT Forum Logo
