Joey Mack
-
Posts
10,049 -
Joined
-
Last visited
-
Days Won
227
Content Type
Profiles
Forums
Gallery
Events
Blogs
BMT Wiki
Collections
Store
Everything posted by Joey Mack
-
How to remove rear diff center on 46160 meritor ?
Joey Mack replied to The Nitro's topic in Driveline and Suspension
The part you are pulling is not very heavy, but I can see where you will have to get creative.. I have the larger tranny jack that Harbor Freight has.. it was under $300.00.. maybe that can help you.. I use mine to do other small lifting jobs and last summer I rebuilt the back box in an Eaton 10 spd. In the chassis.. I used it to pull the back box out.. yes I did weld up a jig to bolt to the table so I could use the yoke for removal and install.. just another idea.. I appreciate that you want to see what you have before sending it out... Jojo -
How to remove rear diff center on 46160 meritor ?
Joey Mack replied to The Nitro's topic in Driveline and Suspension
It sounds like you are going at it pretty good given the dirt floor and engine crane.. maybe a full sheet of plywood under the crane, and some long pieces of threaded rod for guide studs, when it's time to put it together.. as far as breaking the seal, the weight of the diff. Is enough to break the sealant loose.. I'm not sure if meritor uses an internal oil pump, but if so, be aware of the plastic oil gallery, in the nose cone when you pull that apart.. I know Eaton's have them in the front diff. I cant remember Meritors... -
I need a 12 volt starter for my '48 KB-7
Joey Mack replied to Joey Mack's topic in Electrical, Electronics and Lighting
$500.00 for a water pump.. I have no problem trying to rebuild mine, however, it is still working and not leaking. Once I drive it around my neighborhood and get it good and warmed up, I will know better. -
Clean the slope on the front of the carrier housing to left side of the input housing (looking at the input).. Yours should have the letters and numbers stamped in it with a prick punch rather than stampers.. the paint is thick, so a bit of effort is needed.. No Grinders! you will grind the dots right out.. wire wheel in a fast drill or whatever will do... it will show,, the part number/ ratio/and series...
-
when i was at the Mack dealership. we did not do the XT upgrade, without changing the tranny to a 2013/2018 Mack tranny, and replacing the rear ends from 92/93 series to 200 series carriers.. I bet im leaving something else out.. Jojo
-
Welcome Aboard Mainah'.. I lived in Southern Maine for 23 years.. I worked at Maine Mack in Portland. 2000-2006...........
-
I need a 12 volt starter for my '48 KB-7
Joey Mack replied to Joey Mack's topic in Electrical, Electronics and Lighting
G.W. I really appreciate you willingness to help me.. When I get the concrete pad in front of my shop, finished, I plan to put ''Sanford'' there and do bits of work between the 2 engines I am re-building for other folks. I keep acquiring parts and have built up quite a lot of parts.. Mostly for my wiring conversion.. Sorry bud,, I am going through with the 12v changeover.. But he the starter worked well with 12volts going to it,, It is just old and worn out.. the next 2 parts I need will be a water pump and an alternator pulley that will fit on a 22SI Delco alt. for the wide belt that is on the truck.. Thank you, Jojo -
No.... Look at the stool.. do you see a tall silver cup??? It's a,, Triple 'Screwdriver' holder...
-
I need a 12 volt starter for my '48 KB-7
Joey Mack replied to Joey Mack's topic in Electrical, Electronics and Lighting
Thank you.. I will try to get some pictures.. my gauges are a little rough.. oil pressure works, and amp. Gauge sits on zero when running, speedo works, fuel gauge is bad, someday I will get back to working on it.. I have been taking care of other repairs lately.. thank you very much.. -
I have posted about ground wiring a few times here.. search for 9-2 code and follow the ground cleaning procedures..
-
E7 350 Mechanical #6 Cylinder Smoking
Joey Mack replied to Salpolit's topic in Engine and Transmission
when you say ''middle oring'' what do you mean? there are 2 rubber o-rings, and a soft metal sealing ring for around the tip.. there is no o-ring where the injector barrel is screwed together.. -
TJC,,, I just realized you you were talking to Paul.. When you said a very young Joey... did you mean a baby kangaroo???
-
-
You dont know how close you are TJC.. You can ask my wife.. I will taste my dogs cookies to see if they are any good.. The best one's are the this dried chicken tender strips.. Kida like chicken jerky.. Now ''Puperoni's'' they do NOT taste like ''Slim Jim's''.. Yuck.. Just Sayin....
-
Good Idea.. ''Sidetrack area'' will work..
-
Thank you for the starter part number... I spent over an hour trying to find one..
-
mine is 5 spd single rear, my starter has a hole in it.. i could rebuild it and weld a patch over the hole.. Im only trying to make it road worthy for local driving and shows..
-
OK, the rims seem to be 8'' wide from edge to edge... I have a battery cover for it.. this is a project truck and I have many parts in my shop.. I need a starter for it. Im going to change it to 12v negative ground.. it runs good.. I also dont have a crank handle to start the engine either..
-
I dont remember right now.. If I get a chance later or tomorrow, i will look.. I just painted them, so not sure if I can read them. I can go ahead and run a tape measure across.. Give me a minute,, Im gonna look now instead..
-
9.00/20's
-
Once again,,, MackPro comes through..
-
G.W. I see you said you have a K-7 on 900/20's.. I would love to see some pictures... I have A '48 KB-7.. I'm quite proud of it.. I will go ahead and bore the other guys with pic's again..
-
The other looks like an Allison Tranny.. like a 4500... Don't know, but sure is clean looking..
-
It's a big'n... Volvo Green.. I'm curious what it's job is..
-
Harry,, since I got away from Mobile Truck repair...after 13 years,, my work days are not tough anymore.. Its just a nice little place to relax..
BMT Forum Logo
