Vladislav

Any thoughts on how to put it in place of T2090?

Papers tell T2070 is longer and heavier to my surprize.

I probably don't need the nine speed unit for the hobby single tracktor especially the worn one.

Steps look to me too short on my mind in relation to driving a car.

Not shure I need it right now, would have to pay the same amount over for a shipping.

Quick backin' on the road to ya both!

Welcome!

What's the matter of a center point steering?

Is this when king pin center line crosses tyre's contact area right in the center of?

And this way hub comes to the outside with bearing unit to offer more space to move king pin out, isn't it?

The thoughts are the only sad thoughts: a new one or re-chroming.

Nobody will hate you

Just try too keep the way you started to go.

If you're in gym it will work at a long time.

You better don't push your self too much in the beginning but keep it for a while.

Or for a lifetime

And the important thing - always try to be used to like what you do.

And some more specifications.

They were posted on here somewhere some time ago.

Like the rock in 80's and KW, and nice scenery with the firs around the big yellow truck.

And the girl is too nice.

And the most thing I like that you're able to continue doing things you like after that story.

I hope the fact didn't follow some extreme act such as Moon failed on Earth or anything else,

although I'm shure that's a good deal.

Looks like more a good turn out than bad although let's hope that is the end of the story.

Nice pictures, thanks.

Love the R.

American isn't English either!

You're right.

Sometimes I think after being all that time on BMT I'd have bad chances to be understood in Great Britain..

Looks like Vinny aside of the truck on the last picture.

By the word there are T2060 and T2060A with different ratios including OD.

Best wishes!

Too funny, thanks alot!

Will let my sun to read it, nice way to increase English knowledge.

Oh, yea, that's Australian...

I saw them used on e-bay.

Off a B-model and usually need rechroming.

If the memory serves me good I saw them for about $100, maybe for each one?

Great!!

A bit of spray over and it will look unreal real!

How clean is the cab's surface after 3D-printing?

Any traces?

Can you make an up-close shot?

My walkout basement garage got cold enough not one but two pipes froze and then burst, had about 3 inches of water in the basement before someone noticed, I was in NC so the wood stove wasn't running like it is when im here and its cold out. Apparently the water running out the garage doors froze and created a dam and that's how it got to 3" of water in a 22'x42' space, needless to say ive been drying and cleaning since Friday when I got home. I try to keep my wood stove and a fan down there going to keep it about 40-50 degrees but with me out of town it was kinda hard to do, I am trying to get some wood toegether now for the next couple months and guess what, its been so wet I have almost no dry wood. I guess Ill have to prepare a little earlier next year, I already used up almost the same amount of wood I used all last winter, I wasn't ready for it to get this cold this fast and stay there, we don't normally do that in TN.

Good luck on drying all that up.

Good luck on that track but you're probably almost on yet.

I hope for the best turn out.

If you have an interest in the history of Mack trucks and the facilities they used to produce them I suggest you pick up a copy of John Montville's "Mack" published in 1973. It is an excellent book that does a great job of covering the formation and operation of Mack.

I have Montville's "The living legend of the highway" of 1979, brobably a different edition.

Haven't read it completey though.

Many thanks.

A little note - what's about Macungie plant?

I think it's not the same as the Allentown one.

Please correct me if I'm wrong.