Jump to content
Sign in to follow this  
Bigred82576

Axle break down?

Recommended Posts

Hi there I have a 1958 Mack b81sx where can can I find a parts break down of the axles, I need pinion seals and gaskets. Vin # b81sx1654. axle #’s F/R 11kha556p20.   R/R 11kha4134ap20.  815 gear ratio any help would be appreciated thank you.

Share this post


Link to post
Share on other sites

The pinion seals must be the same as CRD92/93 carriers had which were used on R-models and many newer Macks. Try checking Stemco web site. They have online catalog for hub and pinion seals with sizes and discription.

From what I have in my copybook you seals should be :

Front input Mack 88AX458 Stemco 429-0002 4.5x3.5"

Front output 88AX456 429-0008 3.537x2.751

Rear input 88AX457 429-0009 3.996x2.751

If you were saying your truck is B61 I'd say go with the numbers I posted. But you B81SX might have heavier carriers . So better slick under the chassis with a caliper and relate the sizes.

Vlad

  • Like 1

Share this post


Link to post
Share on other sites
3 hours ago, Vladislav said:

The pinion seals must be the same as CRD92/93 carriers had which were used on R-models and many newer Macks. Try checking Stemco web site. They have online catalog for hub and pinion seals with sizes and discription.

From what I have in my copybook you seals should be :

Front input Mack 88AX458 Stemco 429-0002 4.5x3.5"

Front output 88AX456 429-0008 3.537x2.751

Rear input 88AX457 429-0009 3.996x2.751

If you were saying your truck is B61 I'd say go with the numbers I posted. But you B81SX might have heavier carriers . So better slick under the chassis with a caliper and relate the sizes.

Vlad

A B81 could have the 50,000 rears, takes a different carrier, different seals maybe.    terry:MackLogo:

Share this post


Link to post
Share on other sites

They are CRD92/93 rears.Thanks for the info guys. 

Edited by Bigred82576

Share this post


Link to post
Share on other sites

Hi there R/R didn’t work still leaks does anybody have a part # for a pinion yoke sleeve? It’s 2.75 O.D. Thank you.

Share this post


Link to post
Share on other sites

https://www.napaonline.com/en/p/NOS99269

 

"N" Nominal Dimension 2.750 in. / 70.00 mm
Brand Name NAPA Oil Seals / SKF (CR)
Fits Shaft Diameter 2.750 in. To 2.756 in. / 69.85 mm To 70.01 mm
Flange Diameter 3.125 in. / 79.38 mm
Installation Dimension 1.250 in. / 33.32 mm
Seal Surface Width 1.125 in. / 28.58 mm
Speedi-Sleeve I.D. 2.75 in.
Speedi-Sleeve Width 1.25 in.
UNSPSC 31171509

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

×
×
  • Create New...