Jump to content

skydawg

Bulldog
 View Profile  See their activity

  • Posts

    249

  • Joined

  • Last visited

 Content Type 

Everything posted by skydawg

  1. skydawg
    I`m seeing from 150 to 250 ft lbs for the wedges,and some saying not to bother with a torque wrench at all,since there are inconsistencies,eg,thread condition,rust,that vary from hub to hub.Would 200 ft lb be a good number? I`ll be swapping 6 tube rims and tires tomorrow for tubeless.I know to deflate the old tires before loosening any lugs,but this is first time territory for me.Thanks.
  2. skydawg
    I took the fitting to a local plumber shop,he fixed me up w/ the plugs.Thanks.
  3. skydawg
    Thanks.Oddly,when removing,a 15/16 wrench on the flats was too small,a 1" was too big,a 23mm fit perfectly.Would there be a metric version of these fittings?
  4. skydawg
    Hi,new B61 owner here.I want to remove the trailer air lines from the junction behind the cab.Can anyone tell me the size/thread plugs I`ll need? I`m guessing this is an industry standard size. Thanks.
  5. skydawg
    I don`t know what the crud is on these rims,but short of scraping it off,it ignores,in succession;Spray9,acetone,citrus paint stripper and Purple Power.Would steam cleaning work? Thanks.
  6. skydawg
    They have them,Frank,thanks for the info.
  7. skydawg
    Does anyone know of some decent used Dayton rims in the NNJ/eastern PA areas? Thank You.
  8. skydawg
    I need 6,am in NW NJ,will travel.
  9. skydawg
    Hi,is visible smoke from the road vent(crankcase) to be expected or is it indicative of excessive blowby?Would this be a deal breaker for a buyer who couldn`t afford an engine rebuild.The engine seems healthy otherwise.Thanks for any advice.
  10. skydawg
    Has anyone found something from another vehicle that can replace the original,which is all but impossible to find?Thanks.
  11. skydawg
    Thanks Frank,STTC in Bethlem has used rims and tires,I`m told.
  12. skydawg
    Hi,does anyone know a source for these in the Allentown area or a reasonable hike from there? Could use decent used tires,will just be bobtailing a B61. Thank You.
  13. skydawg
    I`d like to know what the 1962 B61 sold for.
  14. skydawg
    Hi,is anyone bringing a B model to Macungie this year to sell?
  15. skydawg
    Two days ago it could be had for $4.99/gal here in NNJ.Today it`s $5.76...WTF?
  16. skydawg
    I should add that I know alot of people that can make large amounts of alcohol evaporate...still no word on the Unishift device.
  17. skydawg
    I`ve read a few tales of an aux case cracking/puking,and hope this is a result of poor maintenance,and therefore avoidable.
  18. skydawg
    I`ve about given up on finding a nice B61 s/a tractor and am looking at a B67 w/ Unishift trans.So this setup has an air cylinder that needs frequent water draining,as well as an alcohol evaporator?Is that something that you fill w/ alcohol on a regular schedule? Thanks.
  19. skydawg
    I guess Vinny has completely abandoned this site...he would have ben raving over this a few yrs ago.
  20. skydawg
    Wow,great explanation,thanks,Weasel!
  21. skydawg
    What sort of mileage could I hope to get w/ a light spec 1961 B61,S/A,END 673,Duplex direct,4.66 dual reduction rear axle,11x22.5 tires,bobtail only.I also could use an explanation of "Dual Reduction",as per the rear axle. Thank You.
  22. skydawg
    I thought you just built a garage and were ready to start the work.
  23. skydawg
    I got quotes from $575 to $2000,some were clueless as to what a Mack B61 is,and what would be involved.I assumed any responders would be lowboy O/O`s.
  24. skydawg
    Hi,I`m looking for someone who can haul a B61 T from Nitro,WV to Washington,NJ,in early April.I`ve gotten a bewildering array of quotes from Uship,Mercury and others,and lots of scary reviews from customers.Any suggestions or leads would be appreciated,thanks.
  25. skydawg
    Thanks,h67,they had a B61T shop manual for 1962,so I bought that.They also have a parts book from 1966,don`t know if that would be a necessary addition to the service manual.

BigMackTrucks.com

BigMackTrucks.com is a support forum for antique, classic and modern Mack Trucks! The forum is owned and maintained by Watt's Truck Center, Inc. an independent, full service Mack dealer. The forums are not affiliated with Mack Trucks, Inc.

Our Vendors and Advertisers

Thank you for your support!

Mack Related Links

Popular links

BMT Forum Logo

HTML tutorial
×
×
  • Create New...