Joey Mack

President Trump could see into the future and protected us and our economy.. Our current President, also saw into the future. He stopped our pipeline on day one, and now our fuel prices are going to reach and surpass the prices from 2005 and so on, all because of the Issues in Ukraine. He planned to cripple our country, and new that Russia's govt. would try to take Ukraine... I wish I was more eloquent, but I'm not that smart. I just call out what I believe I see. It makes me sick to think the appointed one, was put in place to destroy our great country.. Opening our southern border and giving away everything to these Illegals, that WE all have to pay for out of our PAY CHECKS, something that these people dont have a clue about. Not to mention the intentional destruction of our relationship with each other by allowing the claims that all white men are racist, and all criminals need to be free, and we need to understand why they are criminals. Whats next J.B.?

O'Rielly's sells flux capacitors ... Flux Capacitor Part # 121g Line: EB This item is not available for purchase.

I would like to be educated on the S/P switch, not sure if I know what it is... jojo

that little horse shoe tube is a fuel return jumper from head to head.. 7 pieces, buy all of them and replace it all new... no more leak... jojo

the picture is not wide enough for me... I think the oil on the spring is coming from the steering box and not the overboard breather.. I bet it runs fine, just needs more frequent maintenance, if hes not going to roll rods and mains and a new oil pump... jojo

i would think you are a severe service application. wouldnt 150 hrs be correct? I need to look in my maint. and lube book.. I thought I was doing 150 on dump trucks when I ran a fleet. about 4-5 /per year... jojo

we are screwed!!!!

If it runs good and get's the job done.. run it... keep up on the fluids and temperature.. belts and so on, and it will run and run... jojo

"Fix what you know is broke!" Jojo

right.... but the connection itself is not a fused link.. so cut it, and remove the bad wire approx. 1/2" of wire, and solder in good wire if there is not enough to make the connection's.... jojo

I did, however when you first said to parralel them I believe you meant 'series' because thats how you double the voltage. it would make 12 v on each side, then for the starter you would series those cables. and for the cab power you would come off one set at 12 volts... Good chance I F'd this up now... jojo

there is a small pipe plug behind the breather.. you can grab a 10mm socket and remove the breather, clean the area, and run the engine to see if it leaks.. jojo

Yeah.... What he said.....

I think its bit too much blowby, and the low oil pressure when warmed up. 20+ would make me feel better.. when was the last time the oil pump was re[laced, as well as rod and main bearings? the blowby is usually worn rings, I have done rods and mains and an oil pump several times to help improve oil pressure.. Of course I didnt do cam bushings, due to cust. budget or request... it does help. I also check the welch plugs in the rocker arm shafts to make sure one is not leaking by or popped out.. ive made that repair a few times... there will be more comments on the way.. one of us will help you... jojo

Hayseed, I laugh... If you ask my wife, a broken clock is right more times a day than I am.. (2) 6volt batteries makes sense to me.. jojo

I believe, I would cut them to a clean spot and solder in new wire. I would also slide a heat shrink on the wires before I solder them.. I dont think that is a fused link, I believe it is just 2 wires into 1, under the heatshrink.. jojo

I'm guessing it's a 24 volt system with negative ground? I would just check the battery cables for proper routing, and tightly crimped ends. D.C.W. has a good point as well... I assume the 2 6 you post is 26 volts when running... it should be 28.4 ish when running... any thoughts? jojo

My guess is Jessica Is in R+D? I"m Looking for a career change.. Let me know if I can be of service. I can bring my tool box... jojo

wish you well... I believe it s a wiring issue, and possibly a bad ground or 2+... jojo

have you set the sensor in the flywheel housing correctly? all the way in til it touches, then 1 turn out...? same for the speed sensor at the tranny tail shaft... jojo

do you have a robert bosch 7100 pump? send a pic....

I dont know about that, and would not introduce a future issue.. Just take it to Mack or someone with PTT for Mack or a ProLink 9000 with a V-MACIII pmcia card... you can set road speed and cruise speed... jojo

OK. I am curious why you may need another FIC module.. but.... if that what gets you going for a few years, then I guess that's it.. You have one hell of a truck!!! Keep it rollin... jojo

I forgot... did we talk about the sensor in the flywheel housing? jojo

Good night sir, thank you for your kind words... jojo