Jump to content

thomastractorsvc

Pedigreed Bulldog
  • Posts

    3,057
  • Joined

  • Last visited

  • Days Won

    16

Everything posted by thomastractorsvc

  1. I just bought some for one my 89 RW713 of mine from the dealer I gave $94 for Left side and $86 for the right side my numbers were 24RU4135P3 /RH 24RU57P7 24RU4136P3 /LH 24RU58P7 For my 85 RW788 24RU4136P2 LH 24RU4135P2 RH
  2. It has less than 5000 miles on oil, it looks like someone messed with it as the cover leaks and so did the electronic valve. I took the magnetic apart and resealed it. I noticed that it had a combo of metric and SAE and a nut as a washer. I may try and take it apart and reseal it as it seems to be weeping. Or just run it until it give a fit then replace the whole thing for $789.00
  3. I wanted to update, Thanks for the info I try and get a couple pictures. I mounted mine to the the lower tabs on the charge air cooler using 3/8 bolts and a couple washers for spacers. I bought the AC Condenser, dryer and expansion valve form part http://www.partdeal.com/ they are a RedDot distributors and I replaced the evaporator coil from amazon. All in less compressor $331.46, I bought a compressor local $264.51, should have gotten it from Partdeal.com.
  4. Its was active turned the truck off it went off. No smoke or anything out of the ordinary. The timing advance is the ecovance correct?
  5. That little condenser is enough to keep everything cold? Looks like it is only about 8" tall.
  6. Fired up my 92 that pulls my end dump from her winters hibernation. Last ran in about 3 months ago. Took it out to top it off and threw a 3-5 code looked it up says >>Timing Actuator Response Improper << What is that the ecovance or some sensor? Still runs and drives Any ideas?
  7. Anyone replace condenser with aftermarket one? What did you get and what size. My grilldensor was plugged with calcium and oil, thought we got it cleaned out still having problems with charging system
  8. I bought another Granite at an auction, seems to run fine but has 3 codes 2-9 (ASET CEGR) Combustion temperature sensor 3-5 Engine Brake Output #1- This wire was connected 3-6 Engine Brake Output #2 - This wire was laying on the manifold, I reinstalled it and the code did not reset and of course the engine brake does not work Any insite where I can find the Combustion temperature sensor and how to test the engine brake? can you just wire it up like a dynatard?
  9. check your motor mounts and front damper, lot of hours and years on them rubber parts
  10. Heat shields are on, i disconnected the wires and cleaned the terminals driver said that on his last load the code disappeared and truck ran awesome and then it came back on when he fueled . When he pulled it in it was on, he shut it off and a little while latter when I went to check the blink code it was cleared. I think I may change the #6 with one of the others while I have everything apart so if it is heat related I don't have to do it again. Or see if I can afford another one from Mack or just leave it and see what happens. The mack dealer tech when I asked about the stumble said no active codes so everything is working good, asked about the hesitation he said it is supposed to have a hesitation because its an electrictronic engine I didn't argue as it didn't have any active faults and ran good other then that hesitation brought on by the acceleration under load.
  11. I made a youtube video depends on what you got to do and what capabilities and tools you are working with, the video will tell you.
  12. I bought a couple of long bolts and made guide pins it helps with getting the carrier to sit down flush. I use the good RTV and when it's tacky I drop it on I usually have to wiggle it but the guide pins allows it to not make the RTV push out creating a leak
  13. What would you do? 1M2AG11C65M029481 2005 CV713 I paid to have HP increased last year from 350 to 400, truck is still a dog still and the motor acts like it has an old quadrajet carb, stumbles and then pulls out of it. Idles, starts and runs fine except when crowding it especially noticeable under load, but it pulls out of it. I have change filters 3 days ago with no improvement. History of 8-6 FMI 8 & 8-5 FMI 8 nothin recent but until 2 days ago no active faults but has thrown 8-5 FMI 8 everyday I checked for wiring issues and cleaned all terminals cleared code took about 30 minutes and the 8-5 FMI 8 popped back up. I bought a Mack EUP and injector line and bolts today What do I need to look for especially since it is one of the ones that is hard to get to
  14. you can use the speed control switches to get it to flash/blink. Then count the flashes and post the codes. there is two flash/blinks per code so if it was the engine timing sensor that threw the code it would be (Blink Blink Blink---Blink Blink) 3-2 on a V-Mac III
  15. Had that in my 92 RW I was driving in the early morning and it started raining then the headlights quit and I could smell hot plastic. Pulled over and waited until daylight, ended up getting cancelled due the rain so I went to the Mack dealer and spent $20 something on a 15 amp breaker been good since. I ordered some new breakers for it. I took the dash apart and found a couple hot wires just laying inside so I taped them up. Found some barely bare wires on the r/h headlight so I redid them to make sure. I think its something in the headlight circuit. The headlights work on low but if you switch the to high it will kick the breaker or if they stay on the accessory circuit will kick off then the headlights. I always fix bad wiring but without a good schematic its takes a while. This truck has the split headlights ( they don't run off the bus bar) they run out the firewall on both sides up to the lights. I am planning on rewiring the headlights and adding relays and doing away with the dual circuit setup that should eliminate and shorts or touching wires.
  16. Has anyone experienced this. No previous issues I was out trucking parked on Friday. Sunday afternoon I took heater cover off to fix air cylinder. I reassembled everything fired up the truck and ran the fan for a minute or two going through all the positions and checking the vent discharge. The defrosters wasn't that strong, it was blowing out the bottom so I shut the truck off looked in side the side vent and moved the selector and realized I need to turn key on so I did and I got was a clicking noise from the power shut down solenoid in the dash. No power to the dash or lights etc... I pull the center panel off and I am getting 12 volts but its still clicking I disconnect the hot side to the switch it shows 12v and I can start the truck but no power to dash, all lights seemed to work. Hook the wire back up no key or power and it clicks. So I pull the solenoid and test it tests good but I replace it Monday morning. Still doing same thing. So I decide that I must have a open hot I pull all fuses and start replacing them one by one after checking them for continuity, all installed nothing I pull the relays and check them the Emergency Stop Lamp relay has a broken pieces of plastic so I figure it may be grounded out to the aluminum fuse panel. I pull it out of the mount and wrap in electrical tape. I try it and everything works. Run the truck most of today the power shut off to the dash like before, I turned key switch off and on again everything came back about 15 minutes later did it again would not reset so I brought the truck home and switched trucks to finish the day. Ideas anyone? I been thinking of it may be easier to just rewiring the interior as I already rewired the lights to rear and to the hood.
  17. my 2 cents. My buddys tarp motor was acting like that and one of the poles was broken free in the motor. This was found after he brought it to my shop and he already replaced the switch and wire. I disconnected the wires and hooked up to my multi meter they showed 12v ots both sides in accordance with the switch, if you grounded the motor it would work, I told him the motor was bad he didn't believe me so I took one I had and hooked it up and showed him. Took the old one apart and the terminal was broken loose in the motor.
  18. Will do I mostly have been on face book haven't been here on a little bit
  19. No still has it in the jewelry box probably most valuable item in there lol
  20. I finally found a engine so the A54 back on the restoration list. Need a window regulator for passenger door and would take a window if available also (1) A54 hood emblem I have extra A Model series parts we could swap or I can always give you some money
  21. you can see the rust between the frame rails on first picture of the under side right above the air tank. Being it is from Chicago i am sure it has frame issues, the floor pan a has patch panels screwed to the fire wall
×
×
  • Create New...