Moparmike

Are a repair if possible 

2001 ed e7  what numbers are needed off the computer I have to get 

Can someone tell me where all the truck grounds are on a 2000 rd I'd like to check those as well

Turn in a driveway this morning and hit a bump truck just lost all power only idle to 900 code 6 4 had that happen before took batteries lose no more problems..today nothing still no power I took the gray triangle shape plug apart with the green yellow and black wire pull ecm fuse let truck sit no battery hooked up even took the plugs off the computer on the passenger side of motor nothing..just went out on job ..first day and 1 hr on new job..Smh  ..anybody got any ideas to try right here at Christmas is not a good time to be out of work..or even get run off the job..any help is appreciated thank you 

I see there are a few oil plugs on the rear end are they all connected as in does the top 1 feed the bottom are do I need to check and fill each ..didn't want to pull the bottom and fluid goes everywhere..

Anybody know a good source for a pump ..mack here is 770.00 ..but not in stock ..

Ok guys I'm really at a lost here ..I've changed out the 2 on the firewall 1 in the cab still no power..anybody know the location of the fuse inside the cab..or relay that controls them..I still have no brake lights..no power on firewall when pressed or even when I start the truck for the first time to let air build..thanks

Ok thanks ..I replaced the 2 on the firewall does the 1 inside look like the 2 I replaced..airline and 2 wires going to it..

Ok guys truck had brake lights this morning now tonight none..no power to light switch on firewall..is there a relay in the cab or fuse..got dark on me so I didn't get to check alot of things like I wanna get to..all other lights work just no brake lights..thanks in advance 

What's a good place to get 1 from and what all needs to be replaced..mines has a hair line crack running in it above the grease cap ..can it be welded or just replaced..

Where can I find the switch at on the truck under the hood on the firewall..

2000 rd688 if I press the brake pedal enough to start slowing the truck down the brake lights dont come on ..but I I press the pedal harder they work..the work fine when I first start the truck up for the day ..I can be at a stop light sitting on the brake truck still (automatic) no lights push a little more brake lights on..any idea where to start looking..I'm afraid I may get hit..

11gba4269p6

7y0774

Any help would be appreciated. 

Oil pump they said 45 days before I could have it..

1997 mack e7 427 

I need cam and lifters kit found a company close but they asking 2700.00 but it has stiff that we don't need ..eup rollers are in great shape but comes in the kit..

Well found out today that it's a E7 427 in the truck ..got in touch with the guy I got it from..1999 model..so what's the thoughts on this engine guys .looks like new cam and lifters 1 lifter is beat up and the lobe on the cam matches..push rods are good to go rollers on eup are good to go 1 cylinder has a few scratches that I'm not comfortable with also going to put new cam bearings in..

I had 1 jump out of my e7 2 times come to find out the clip that holds the roller on the bottom was bent after 1400.00 to fix the first time I took it apart the 2nd and the roller fell off in my hand bent the sides in just a little no more problem in over a  year..

43 minutes ago, KKERGALL said:

11GB1716Y

E7 460 E-TECH

 

Did you get thos from the above or from the vin..just trying to make sure of the engine  in the truck..hopefully it's not been changed 

2001 mack rd6886 ..I was told e7 350 but not sure valve cover been charged..now I have to do a cam job so I wanna just make sure I get my right parts and know what I have ..that's the vin. Off the title ..thanks

Ok guys I have some numbers off the passenger side of my engine I was told that they would help me in the engine info area..someone change the valve cover on my engine..so if there's Anybody that can offer any help I would appreciate it very much ..

Looks like 

7y0774

552m.  3740.    1272

Stamped under the eup in a flat spot ..mack told me that its either on the drivers side by starter or by eup and thos is by eup ..thanks again guys for all the help 

I think he knew looking over the paper work he hadn't long purchased the truck himself..he has 5 trucks now so this explains why he got rid of it I guess..

Well looks like cam is bad ..would I be better off get a used motor or just fix what I have ..just purchased this truck ready to get it out to work but now this..2001 E7  460 quint axle dump thanks for all and any help guys 

Valve cover been charged for some reason..

Do you have to be a member to get parts from pai

23 hours ago, Mack Technician said:

I’d replace all lifters and followers unless it was a ceramic SetUp. Oil pump. Bearings. Check updates to brake pins, etc. Last I checked PAI will sell a complete camshaft kit and Mack made you itemize. Guys at the dealership we’re giving the blessing to buy the complete kits from PAI. 

Nice hard working rig, good luck!

what’s it power to? HP?

I was told 460 but I'm not sure just picked it up last week..where are mack serial number on the block 

23 hours ago, Mack Technician said:

I’d replace all lifters and followers unless it was a ceramic SetUp. Oil pump. Bearings. Check updates to brake pins, etc. Last I checked PAI will sell a complete camshaft kit and Mack made you itemize. Guys at the dealership we’re giving the blessing to buy the complete kits from PAI. 

Nice hard working rig, good luck!

what’s it power to? HP?

I was told 460 but I'm not sure just picked it up last week..where are mack serial number on the block