Moparmike

I just did about the Samething as you I purchased a excavator but I got my gladhand kit from anything trucks haven't Installed it yet but seem to be everything I need bunch of good videos on YouTube I just need to figure out the trailer wiring now before the gladhands

when I unplug the oil sensor on top of the filter shouldn't the shut down light come on or shut the truck off sorry 2000 rd688 e7 400 my shut down ligh. comes on randomly and shuts down sometimes not all but fires right back up I've changed water level sensor water is full oil is full I could really use some help I haul asphalt for a living and I'm afraid it might shut down not start back up thanks

ok guys my shut down light got where it comes on when I hit breaks hard at a stop or if I have to stop suddenly I changed the water level sensor still no change . what can cause this where should I look every now and then it shuts down but only when I'm stopping both tanks are full thanks guys

2000 rd688s e7 400 hp Eaton 8ll transmission truck is a great truck works everyday I have a new truck ordered and don't plan to deal with drivers anymore I've had enough rear bushing will need replacement soon truck has new floats on the front new clutch and flywheel demolition body with high lift gate I've replaced the turbo yrs ago and 1 eup everything else has been basic maintenance done I'm asking 40000 cause Bushing will need replacement there not walking but I feel a vibration or bump in the rear and a pay attention to the Rear-end

I replaced the vent a while back that could have been the problem it was leaking before I got hit but I was thinking it was the side cover

I see my bushing are about gone or gone I feel a little vibration I'm sure it's coming from the rear I was hit in the side front to back about 8 months ago and I could see where the spring had hit the saddle it was put on the freak machine and alignment machine was told in spec but I see the bushing the rear is moving back and forth not alot but it's there all tq rods was replaced bout a year ago is this a tough job or can be done at home with normal tools if possible I'd like to replace with greaseable set up

ok guys looking my truck over I see the grease is coming from the seal that's behind the big nut holding the rear yoke in the rearend is this something I can do or need to be done by shop I know on my race care it helps with the lash specs but not to sure on this

yes sir mack rears just trying not take them off miss work before I get some to swap out

2000 rd688s anybody have a good part number I'm trying to order some online but wanna be sure I get the right parts mack said they couldn't give out part numbers imagine that 😳

hey thanks I found the other post my cover is aluminum thank you

anybody have the part number for the oring that goes in the side cover on the mack rearends driver side cover 4 bolts I'd really appreciate it means has developed a little leak thanks guys

up date I wanna Thank You Guys your so amazing and helpful I took the plug from the bell housing and pulled on it like Joey Mack told me and It was hard to pull cut the tape on the wire loom so I could feed it back to the top beside the motor I pulled again and the connection was easy to pull side ways 1 out the 2 wires had been repaired before and came apart I clean everything up striped the ends twist them together just to check see if that was the problem and boom fired right up code light is off I truly appreciate each and every one of you for your thought suggestions and help especially Mr. Joey Mack which has been in contact with me through messages I still have other stuff I need done mr.joey Mack I have your information and will still be in touch to get you to work on other things on this truck soon again thank all of you guys

that was me truck has been in the shop guy ran into me and bust my fuel tank

I really need to get it out to you I'm outs Raleigh not far from you great service is always worth the ride if you don't mind send me your contact information 🙂 thanks

I'm kot sure but it ran fine for a few weeks after it was installed they could have damaged the wire installing the new stuff they removed the fuel tank and everything on driverside

I'll check that this week it runs with the sensor out unplugged at bell housing I hadn't thought of a bad wire or plug I did spray the plug with brake kleen to clean it out when I installed the new sensor

e tech I believe it's computer control it has the sensor in the side of the bell not front I had a shop replace the clutch and flywheel

yes tech and mph works speedometer and hr meter does not work it stopped a while back

my old 2000 rd690s 300 e7 Allison auto was a great truck kinda slow but I'm Pais hourly lol

also the flywheel was purchased new not resurface buy not from mack from another parts supplier mack had a long wait time this is my only truck income right now

no real concern of the flywheel what's just told it could be the issue so where do I start I pulled the bell housing sensor and it would run but I replaced it with new from mack anyway then pulled cam sensor no start at all and thanks guys I really appreciate your help I really need this truck fixed

ok guys I had my clutch and pressure plate replaced months back a few months after I got a 3/2 code while driving down the rode I checked code it's speed sensor I replaced both in bell housing and tail shade code still there now the truck has lost some power cause now I have to down shift more to climb hills that I never had a problem on also the truck is hard to start have to keep turning g ot or either spray it for faster start even after it's hot it's kinda hard to start but not as bad as first start of the day I'm thinking ring gear has moved on pressure plate if I remove the sensor in the bell housing truck will still start but still hard if I remove cam sensor on front the motor the tru k will not crank any guidance would be great this has been a great truck last 4 years but I can't keep dealing with it as it is now thanks clutch from mack pressure plate from outside source

trying to locate a fuel tank close to nc if possible tank is about 34 long 24 wide filler neck bout 7 inches from back of tank aluminum tank thank you for any and all help

Can anybody tell me where to find this fuse I don't have a diagram for this truck Ac stop working yesterday and it's 78 at 715 am Freon is in system been working great just stop going down the road 1 wire connection was coming out sometime so I'm thinking it's blown a fuse Going to put in a new connector to fix that issue Also my truck has a bunch out metal looking fuses not regular fuse how can I check these fuses