Jump to content

dgk1

Puppy Poster
  • Content Count

    13
  • Joined

  • Last visited

Community Reputation

0 Neutral

About dgk1

  • Rank
    First Gear

Profile Information

  • Location
    va
  • Interests
    racing, hunting

Previous Fields

  • Make
    mack
  • Model
    cxu613
  • Year
    2009
  • Other Trucks
    94 ch613

Recent Profile Visitors

525 profile views
  1. dgk1

    loud chirp/whistle MP7

    Was there any power loss from the exhaust leak? I'm having same sound but losing power and boost when I hit any kind of hill that requires mashing the pedal.
  2. I have a 1988 Mid-Liner. I believe it is a CS300. It has the six cylinder Renault in it . Between the second and third cylinder it is leaking something I'm not sure if is coming from the valve covers or lower, I'd guess lower.It sounds like a air leak but it has a rhythm. It gets much quite as the truck warm up.There is some oil in the area. Anyone have an idea ? Thanks Tom

  3. dgk1

    Intermittent power loss

    I'm not sure. It only does it on interstate. I can run all day off the interstate and it's fine.
  4. I have a 2009 cxu 613. Problem I'm having is getting up to speed on interstate and maintaining it. The last couple gears, the truck just seems flat. Once up to speed if you come up on a hill you feel it stop pulling and boost pressure drops. Sometimes you can ease off the pedal and it picks back up. Any ideas on what to look at?
  5. I have 2009 cxu. I'm getting a code for #5 injector. Went to replace it and the part number they gave me is #85013149. The number on the one in the truck is 85003656. Is this and updated injector or just wrong altogether?
  6. I have a 2009 cxu and am not getting power to suspension dump switch as well as power divider and PTO switches. What would they be listed under on fuse panel?
  7. I have an 04 cx 613. It stopped building air pressure had to tow in, went to replace compressor and noticed the gear on shaft going into it just free wheels. Is this normal or do I have another problem?
  8. Same problem again. Does anyone have any other suggestions?
  9. Ended up being the plug on one of the wire harnesses.
  10. I checked and cleaned grounds battery terminals all computer connections and still no luck. Will turn over but wont start
  11. I have a 2004 cx 613. It started running rough yesterday like a fuel problem. When I checked it, had 8-3,8-4,8-5, and 8-6 codes. I cut it off and started it back up and had 1-3 and 2-7 code. Checked connections on computer and wire harness. Started back up idled rough and had 9-2 and 6-4 code. It cut off on its own and won't start back now. Shows a 6-4 code when you turn the key on.
  12. I have a 2000 cx 613 with etech 427. I just put a cam in it along with new rods,mains and oil pump. Also put a new head on it. I started it for the first time today and it has a rough idle and then smoothes out as you run it up to around 900- 1000 rpm. Figuring that's the valves need adjusting. I ran it for about 35-40 mins and the oil and water temp was almost at redline. What could cause this? What do i need to look for?
  13. dgk1

    2000 Cx Engine Problem

    it is a loud noise like a gun going off inside the engine. sounds like its toward the left front of the motor.i pulled the valve covers off but don't see anything broken or out of the ordinary.
  14. i have a 2000 cx613 with a 427. the engine started losing power today and making a loud noise.i had one person say it sounded like a dropped valve so i pulled the valve covers off but i don't see anything wrong in there.what else can i look at? it also shows a 1-1 code now.

Welcome to BMT!

...The world's best antique, classic & modern Mack Truck support forum! Founded in 2000, BigMackTrucks.com is the place to go for everything related to Mack Trucks!

BMT!

BigMackTrucks.com is owned and operated by Watt's Truck Center, New Alexandria, PA. This forum and it's contents are not affiliated with Mack Trucks, Inc. or Volvo Trucks North America.

×