Zeuz

No the starter hasn't been replaced at all ..my driver just called and said he got no dash lights ,still no turn signal or radio no cruise control...but if he turns head lights off the rpm and speedo gauge lights up...the only thing done to that truck in the last 2 weeks is it wouldn't go over 55 and mechanic eliminated the protection mode on it couldn't find what was wrong or just being lazy...

No the starter hasn't been replaced at all ..my driver just called and said he got no dash lights ,still no turn signal or radio no cruise control...but if he turns head lights off the rpm and speedo gauge lights up...the only thing done to that truck in the last 2 weeks is it wouldn't go over 55 and mechanic eliminated the protection mode on it couldn't find what was wrong or just being lazy...

Hey ,I'm having trouble with my 2011 mack ,the turn signals won't work,radio,cb,and the dash lights don't turn on.but if I turn my headlights off the center of my dash lights light up..the control center with the amps,miles etc come on and off..the other day my batteries went dead I replaced them and put new alternator and everything worked fine ,but I'm having this problem...anyone know what can it be...my driver says all fuses are good.thanks

No ,he hardly ever test drives just the computer.....i priced that tube at mack it was 1900.00..i have no issues getting it but i wanted to double check first...thanks for the info..i just got the truck a few weeks ago for my lowboy..the gauges will work the quit it cuts on and off...does that have anything to do with it u think? Wiring or so

Ok im going to try that first...the mechanic wants me to replace the tube with the EGR control .but i wanted to see if it could be something else...thank you

I have a 2006 CHN 613 it won't go over 63 mph at 1600 rpm that's all it will do it has a 18 spped.... I took it to a mechanic he said it's reading Egr- mass flow-open ( flash code 5-9). Before he goes guessing and replacing parts ..i was wondering is anyone has had this code or knows anything about it...

Have a 2011 mack with a MP8. The ac was cooling while u was moving on the highway.but idling it won't cool blows hot..it just went out today doesn't cool at all..the engine fan comes on at 205 degrees but i don't hear it coming on while idle..i wired the high pressure switch straight but u hear it click at the fan but it won't engage .it's a cool logic cooling fan ..wondering if it's the ac or the cooling fan or both..thanks

They wanted 10,700 for a reman transmission and 2,200 for the labor..plus at the other extra...at the dealer..I'm in Florida a place in Georgia that works on transmission only quoted me 15,000 and they would come and get the truck I had to pay for fuel only

I took the truck to the Mack dealer ship..they put a new clutch,flywheel,clutch actuator ,clutch valves,clutch cylinder,solenoid valve,brake switch with wire harness. 7,400.00 dollars .it now runs perfect,it will get up and go no problems at all..

I will

I'm having a guy to do it ..he told me $2,500 for transmission with pedal,and everything needed around 4,000 to ,4,500 ...so I'm thinking I will have around 6,000 with everything..installed ready to go...I average 750 miles a day pulling 88,000 so I need it to last...

I hooked up a loaded trailer today and it ran 55 plus mph..got to 11 th gear wouldn't got into 12 th.with the pedal all the way down the transmission started to slip a little so I'm figuring the transmission by slipping it's not letting get up in speed...Mack quoted me $32,000 for a new MDrive 12 speed,or 11,500 for reman plus 2400 labor..I'm going to pull the transmission out and put a 10 speed manual.getting away from aotomatic..too much money..

Thank you

The same shop who deleted it programmed it.....this shop deleted the truck a year ago and it did the same thing no power at 50mph but the programmed it a got it right......now a year later doing the same thing but the can't get going ..they tried everything...so I took it to another place and they telling me they don't see anything wrong with the program..so I don't know