Hayseed

A quick google search came up with this....

https://www.napaonline.com/en/search/replacement-parts/steering-and-suspension/tie-rod-ends-and-sleeves/heavy-duty-parts/mack/r700/1983/201579881

I realise the year is Different, But. Take your Old one with you & they should be able to Match It up...!!!

 Draglink/Tierod Ends are very common generic Parts...

11 hours ago, High Binder said:

He commented on a thread Mar 23,2022.

That He Did...

https://www.bigmacktrucks.com/topic/31725-those-hayes-clipper-100-coes/?do=findComment&comment=493011

Here in Australia, the Anthem is AMT only. the rest of the Range manual is a Option. However with the Titan & Superliner The Manual is Limited to 600Hp. If you want the 685Hp It's AMT only.

11 hours ago, 880joe said:

Maybe the people on here with more knowledge than Len could help him instead of make fun of him

I wasn't making Fun of Len, (Far From It) I was Merely pointing out that He had revived a Thread that was one Month short of 10 years Old, since It's last Post....!!!

11 hours ago, 880joe said:

all he was trying to do was help another member on here with a problem

The Member in Question only has made 4 posts Forum-Wide. .All in this Thread from 10 Years ago. & who hasn't logged on since then..!!

The chances of RNRLOBSTA reading & making use of Len's Posts is (IN My Opinion) Slim to None....!!

9 hours ago, theakerstwo said:

Len get back in here we would like for you to feel welcome in here

I wholeheartedly Agree...!!

You clearly have real-world Practical Experience in working on Mack Product. Which(In My Opinion) trumps Theory & Book Knowledge every day of the Week..!!

17 hours ago, Swishy said:

Hay

seed

gudday m8

U need to add these sharp lookn pix from our forum

and the story of the detroit Devil

 

 

 

And the story that goes with it

https://www.hcvc.com.au/forum/truck_Chat/12595-detroit-devil?start=0

Thanks Swisho, The Link is well worth Reading. The Truck Pictured Beat Tyrone Malone's Purpose built Drag truck by 2 Seconds (14.8 seconds for the 1/4 Mile) & was a Fully registered Truck that went back to Work on Monday..!!

17 hours ago, Vladislav said:

Does this superdog run novadays?

Yes It Does.. Photo is very Current (Taken in April 2022)

Not being Rude Len...BUT, you're 9 Years & 11 Months behind the Times.....🧐

31 minutes ago, JoeH said:

Not sure what the road call was, but you have to have a minimum.

I'm with Joe, I'd also send a Bill to the No-show..!!

He Might learn not to take you for Granted..!!

19 minutes ago, Joey Mack said:

  I got pissed and took the little clamp plates out, and the issue stopped.

7 minutes ago, Mark T said:

  I think they may need to vibrate a bit without the metal clamp plates

Not Mack related But in the same vein... 

40Yrs ago My father Bought a new 4240 John Deere Tractor, & one on the Fuel Lines Cracked. He got a new one under Warranty, But In the packet with the New line was a Diagram of where the Little Clamps needed to be to stop the harmonic Vibrations which caused the Cracking.

I remember that Factory Placement of the Clamps was Nowhere near where they Needed to Be according to the new Diagram...!!

Yep, just like when you pull the Plug in the Bath/Sink our Water circles the drain the opposite way to you Guys..🛁

sgosine577 Hasn't logged in since October 2018.. So I very much doubt he'll reply....

As an aside, There's a Guy here in Australia who Sells an All Aluminium & Brass replacement manifold..!!

It's a Million percent better than the POS Genuine Plastic One..

1 hour ago, 70mackMB said:

l saw recently that W. D. Fries wrote a jingle for "(Old) Home Town Bread". Which became the song "The old home fill'er up and keep on trucking cafe"    .....Hippy

He also did the Voice over for the Ads too.

14 minutes ago, Joey Mack said:

I wonder if a 'moderator' can clean it out for us..? 

I Don't think so Joey...

I too have to go through & edit each & every Post. Just like you have been. (If there's another way ? I'm unaware of It)

Be best to send a message to One of the Admins, as they have "Back Room" access ..!!

https://www.bigmacktrucks.com/staff/

4 minutes ago, doubleclutchinweasel said:

My favorite was "Wolf Creek Pass".

Mine Too..

On 4/8/2022 at 12:07 PM, Bullheaded said:

And spy photos appeared of the replacement which we ALL knew was coming

The slippery Slope just got a LOT Steeper......another once proud Truck maker prostituted into obvilion..

11 hours ago, Dirtymilkman said:

Plus with the xdn2's, when you're done with them they still have casing value.

You obviously have a Good Tyre Management in Place.. You could Cap your Cases using Michelin's recamic Process & do It all again & again..

2 hours ago, Onyx610 said:

I wouldn’t say it needs an engine.

You would Hope Not... These days Most E9 parts are made from Unobtanium....

8 hours ago, Joey Mack said:

I stopped advertising a while back because I have many customers, and they keep me steadily busy, and they tell others about me which helps too......

8 hours ago, Joey Mack said:

I am only 1 guy, and I get backed up quickly, 

The last thing a One Man band such as yourself needs is Too much Work.!!!

. People Start complaining about you taking Too long to get to them... (Ask me how I know This)

If You're steadily Busy, I would just keep doing what your Doing. .Word of Mouth advertising is the best there Is.. Also You have a wife & young Child (or is It Children?) Best advice I ever got about being a parent is; You can only watch your Kids grow up Once!! 

You need a good work life balance, & It's pointless being the richest Man in the Cemetery..

Just My 2 cents worth..

32 minutes ago, tjc transport said:

i am still waiting for he drive from home option to be developed and perfected. 😁

They're Close... It's becoming quite common in the Mining industry Down here .

https://www.australianmining.com.au/features/remote-control-mining-in-a-time-of-need/

On 3/22/2022 at 8:56 AM, tjc transport said:

easy off over cleaner. 

put it on the letters and let it sit for 20 minutes or so. 

^^^ Plus one to This..