aw12345

We have atleast 5 of them in Ontario CA all gas V10's

from what tech support told me we need to upgrade to tech tool 2.04 and we should be good

New fangled stuff gets better eh. Overall our Macks are doing pretty well since the oil press issue got resolved. Neither can you beat Mack's waranty

Any input on the fan clutch conversions for the MP7 and MP8's It's a good thing to get rid of the big oil filled clunker, however we are having trouble with getting the ecm's reflashed to get them to cycle properly. There are two versions a smaller oil filled one that is electronically controlled and the Horton air fan clutch. We had a mobile guy from the Mack dealer come out and he couldn't find the correct reflash either.

We are pretty religious about changing air dryer cartridges. Haven't found a single one yet that had oil in it. We have found some that had carbon from the exhaust in the solenoids and ports. Seems like exhaust gas feeds back through the injector

Any known worthwhile resolution for the prematurely failing diesel doser modules and injectors? On our trucks it seems to be twice yearly tradition to change these. The older style diesel doser setup is way more reliable and trouble free

Pretty sure Mack specifies 350.000 miles for a dpf cleaning

Have had a similar problem with several of our trucks. behind the instrument cluster on ours is a data cable to the driver timecard data communication unit that plugs in to a 9 pin connector that Y's of the diagnostic connector which seriously messes with the 1939 communication. Unplug the cable for that Y connector if you have one and see what happens. Doesn't hurt to check ohm resistance between the yellow and green wire at the diagnostic connector with the key off. Should be 60 ohms plus or minus a few

You might be on to something, since they switched to 10w30, which is a requirment for their delivery van fleet, the problem has definitely gotten worse.

Not that steep ,just a long constant grade on the highway. The grade is brutal on a hot summer day it's hard to keep count of all the cars and trucks that overheat on the side of the road. The main point is that just about any 2010-2011 Mack truck with a MP7 engine that goes over that grade comes up with this issue. Also what is the oil pressure spec for these engines? And would high engine load, low RPM into high a gear and the resulting heat built up and then the piston cooling jets spraying more oil have something to do with it?

Oil senders are good, All the trucks (about 20) have had all but the last update done to them. This is not just one truck, almost any one of them, will do this when they drive it up this fairly steep 15 mile long hill climb

Almost all our Mack trucks with the mp7 engine seem to experience a low oil pressure problem when pulling long grades. The engine warning light will come on and the pressure gauge will read low oil pressure and not long after the engines will shut down. This only happens going up a long fairly steep grade, but numerous of our trucks do this. The upgrade tomthe engines for the oil pump idler gear or what ever upgrade required the back of these engines to come apart has done. Anybody can give me a cure for this problem. Not a good thing when a fully loaded truck goes up hill and the engine dies. Thanks in advance

Several codes Kept popping up ran the test to clear the derate , def pump just kept running but would not built any pressure or inject any def. Both trucks are still at the local dealer. Whats with the latest greatest upgrade to the EGR differential tubes? Seems like they did a pretty radical upgrade on those.

We have 20 of the 2010/2011 Mack trucks with the mp 7 engine right now we have the third one with a def problem first one has a harness problem, on the last two the def pumkps activate but will not built pressure. Is this a pump failure? The pumps on both trucks run but will not built pressure. Is there a serviceable part in the pump or an electrically activated valve that causes this? Thanks in advance. By the way all 3 trucks have around 200.000 miles on them

Thanks, will try the back in service tomorrow, if not will do the back to back regens. I have seen the DEF pump loss of power code on about 5-6 different trucks now all with a milage between 200.000 to 300.000 miles. 1 2011 MP8 and the others are all 2010 MP7's. Corrosion isn't a terribly big problem in our neck of the woods even though we had to replace a bunch of engine harnesses on older Macks. On the MP7's we have they are all getting new harnesses and the oilpump updates, that have anything to do with it?

So it just needs to be driven? ran about every test I could with premium tech tool and the system works fine all other active codes went inactive and all tests passed. Another question a I am seeing loss of power to the def pump code pop up on more than a few of our MP7's and MP8'sw is there a common issue with that? Thanks

This truck was driven till the src system derated to 5 mph. Got the derate resolved and the def system working again. Now I am stuck with a active code 128 fmi 14 which comes with the cryptic description special instructions. The driver information display informs me that the 5 mph derate is cleared, but the system is evaluating DEF quality. Where do I go from here, this truck needs to be on the road tomorrow Thanks in advance

My heart has always belonged to Volvos. Grew up around those trucks is all my dan and his brother ever ran. This is one of them from a very loooong time ago

Happy turkey day Y'all

Thanks! Will see if they are willing to cough up the coin

Thanks and got a link to that class? Also what's the cost? UPS is pretty stingy as far as training goes, but in the long run it will save them a ton of money

We have a bunch of 2010-2011 and 2012 Macks and access to Premium Techtool. After initially hating this program, I am getting more comfortable with it and finding tons of usable features. The problem I am having now that there is so much of it that it would take to much time to go figure it all out. Essentially what I am after is a good diagnostic/ drivability manual that also shows how to use many of the features in Premium tech tool. There are just so may choices and play buttons. The more I use the program the more I am impressed with all that you can do with it. Some of it just seems a bit overly complicated. Any help as to which manuals to order and where to order them would be greatly appreciated. Aside from all the older Macks we have some MP8's and a slew of MP7 engines in our fleet Thanks in advance