chana1634

I have a e7 350, and I notice engine light keeps coming on, but when I check all good, now I notice that water was leaking for plastic cap, on water tank, this one has a small peephole, and notice water coming out of there, I remove the rad cap, but did not notice any pressure out of normal, can any body has had this same problem, or any idiea of what to check. thanks for all your help.

thanks guys for your help, just got the diagram but came at the right time.

multiply the teeth on the pion by the teeth of the ring gear, and it will give you the ratio. and yes some pion have the ratio stamp, but not all of them.

Hello everybody Hope I can get an idea here from you guys, my rd688 Is lower on the right side, I notice that the u bolts, are very close to the frame, and also right side back by were the pads goes, the tip of one of the spring leave is also lower that the left side, can any body tell me what's going on here, or if someone had a problem like this before, I thanks you all for your help

hey guys, well I when and took the time to remove the injector, and found that the O-rings, were blown out, bad, and the same time took injector to get tested, and found this injector got damage, my guess is that some Teflon tape got in the injector and plug the injector, got a new one and install, engine run, good, so never install Teflon tape on a leaking fuel line, just replace the line and remove the the injector to check O-rings, at the same time get it tested. I thank all of you  for your tips, sure help a lot,

I had a fuel line, leaking #2 I first remove line, and put sealant tape, but I notice that fuel was getting in engine, when and got new line and install, new line that fix that problem, but I notice that when I start engine it kinds to has hard start, and some white smoke like when I install the new line and air got to the system, after engine runs, It clears up, but when getting to normal temp, and I'm loaded the engine has a miss, and I feel some power lost, now I check injector and #2 is little cold than #1, but not by much, now I turn engine off and let it cool for 3o minutes, and start again and it don't start smooth, it start a little rough, like in the morning but less,  I wonder if the transfer pump is going bad, or any body has any idea, I thanks you all for your help.

thanks, i ll do just that, funny thing is that the right side, got lose once before, and now while pushing snow, hit a bump, u bolt came of, move my axle back, big damage, thanks again for your help.

I like to thak you all for your tips, will try the braker, and all tips, and yes i ment to say strobe, jejeejj, english is my second language,

I just broke my front suspetion, and I'm puttig together but I'm not sure what is the torque speck for the front u bolts, also if you have the torque spec on to the rear u bolts, will be nice, I thank you for your help.

size of wire, not sure same size that is on most of the wiring, on truck, now sometime work ok but most of problem is when snow, or rain,

Does any body have an wiring diagram for rd1999 rd 688 also the fuse panel diagram and position, I thank for your help

Hellow everybody I install a prove ligh, and rear led light, for emergency, while pushing snow, but when i hook, the light for the salt spreader, after a while, lights start flashing, and then go out, I install all out of the fog light switch, that was not been used, i wornder if I need like a new braker or fuse, when i touch the swithc for fog or light is hot, i all ready check for short, but all good, I will apreciate all help, thanks.

I have a 1999, rd 680, mack, and I like to install a torque arm, from the rear to the chasis, to minimize my front axle, movement, when I turn to the right, all ready change trunion bushings, does any body have a part number, for torque rod bracket that attaches to the rear end housing, I thank you for your help. or if you have the braket and rod you want to sell,

I like to adjust the valve, on my truck, does any body have a chart or procedure in how to adjust valve, and engine brake, and or when is a good time to do this, my engine has 250,345 miles, only. I thanks for your help,

Thanks for the information guys,

Hi everybody, I like to know if I remove my tire's that are 11r24.5, and install 11r22.5, will increase speed, and lower rpm, or decrease speed and increase rpm, my rears are 4.47, I beleave, I thanks you all for your help.