Jump to content

Jason Chernoff

Puppy Poster
 View Profile  See their activity

  • Posts

    24

  • Joined

  • Last visited

 Content Type 

Everything posted by Jason Chernoff

  1. Jason Chernoff
    Thanks. Looks like my battery disconnect is shot. Jumped the 2 terminals and everything works
  2. Jason Chernoff
    Truck was running fine. Shut it off and went to restart 15 mins later and no key power. Is there a fuse that controls this or a relay?
  3. Jason Chernoff
    Thanks a lot. I’ll get it changed
  4. Jason Chernoff
    Light came on all gauges are good SA 0 SPN 153 FMI 7 These are the codes I found
  5. Jason Chernoff
    Ok. Pulled relay and they quit coming on. I’ll start by changing that. Thanks.
  6. Jason Chernoff
    Truck sits for a couple days and headlights or daytime running lights come on by themselves. Cannot shut them off unless disconnect battery. Reconnect cables and lights go off for a couple more days
  7. Jason Chernoff
    Does anyone know what the latch/set switch is for on my 2012 pinnacle ? Does it have something to do with the jake? It has an mdrive trans
  8. Jason Chernoff
    What is the proper way to engage a pto with a mdrive trans? And should it be idled up to around 1200 rpm? Using it with a hoist and grain box
  9. Jason Chernoff
    Thanks. I check it out
  10. Jason Chernoff
    I have a 2013 pinnacle with a mdrive trans. Truck is new to me and when I engage the pto to use the hoist it doesn’t always engage and sometimes kicks out after a few minutes. Seems to loose a lot of air when engaged and won’t build anymore . Stays at about 100psi. Can’t find any leaks
  11. Jason Chernoff
    I have a 2013 pinnacle with just the maxx brake switch and no jake. How do I know it’s working? Doesn’t seem to make a difference on or off. It’s on a mdrive
  12. Jason Chernoff
    That was the problem exactly. Thanks for the tip!!
  13. Jason Chernoff
    Truck worked fine. Changed batteries and started it. Now SCR fault derate in 45 mins comes up and DEF level gauge shows empty. I’m sure this is related. Where do I start?
  14. Jason Chernoff
    2013 pinnacle with mp8 engine. Jake not working. Just a 2 position switch. I assume on and off. Switch lights up when turned on
  15. Jason Chernoff
    It’s a 2006 Vision, with a 427 and 10 spd eaton auto shift. Will work great most of the day and sometimes several days. Then you put it in drive and it won’t shift into 3rd. Then usually you get ** on the display or _ or 00 along with flashing arrows
  16. Jason Chernoff
    Display goes blank and won’t shift
  17. Jason Chernoff
    Ok thanks. Thought maybe I’d get away easy and change the alternator
  18. Jason Chernoff
    Hello.. I have a 2006 vision and the voltage light came on. Gauge shows 14.5 volts in the yellow area. Occasionally throws the shutdown alarm. Would it do that if the voltage is to high?
  19. Jason Chernoff
    Ok. Good to know. Thanks
  20. Jason Chernoff
    There it is!! Had to pull the oil filters off. Tucked up behind the second one
  21. Jason Chernoff
    Thanks for the reply but my filter set up is way different. 2 spin on and additional centrifugal . Just pulling my hair out.. there’s nothing on or near filter housing
  22. Jason Chernoff
    Thanks for the reply but that’s where I’ve been looking and it’s just not there. It started acting up and have a new one coming but just not able to find it.
  23. Jason Chernoff
    I have a 2006 Mack with 427 acet engine. Where would I find the oil pressure sensor
  24. Jason Chernoff
    I have a 2006 Mack with 427 acet engine. Where would I find the oil pressure sensor?

BigMackTrucks.com

BigMackTrucks.com is a support forum for antique, classic and modern Mack Trucks! The forum is owned and maintained by Watt's Truck Center, Inc. an independent, full service Mack dealer. The forums are not affiliated with Mack Trucks, Inc.

Our Vendors and Advertisers

Thank you for your support!

Mack Related Links

Popular links

BMT Forum Logo

HTML tutorial
×
×
  • Create New...