Jump to content

dusty0791

Puppy Poster
  • Posts

    14
  • Joined

  • Last visited

Location

  • Location
    Sask

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

dusty0791's Achievements

Apprentice

Apprentice (3/14)

  • First Post
  • Collaborator
  • Conversation Starter
  • Week One Done
  • One Month Later

Recent Badges

0

Reputation

  1. Just cleaned out rad and intercooler gonna try it Monday. Last oil change was about 8000km ago and the valves were set 2 weeks ago.
  2. If it were a worn cam why would it do it only when it's hot tho? It seems when it gets to mid 90s outside is only when It does it and only later in the day also
  3. i have a 1996 ch600 with a e7 427 about 18000hrs and 800 ooo km when the truck is warm it seems to have a noticable miss not when pulling but when i let it idle around 1200 all the war up to 1800 rpm seems a little short on power than what it was a month ago, also seems to run a little warm 210 215 just about redline on temp guage and pyro is 900 it will hit 950 if i keep my foot in it, new air filter and new coolant also new fuel filters not to sure what else to check any help would be nice thanks
  4. The clips going into the valve covers are good and I tried different relays and they all do the same thing. If I jump a wire from a hot 12 volt to the panel where the relay is it just sparks indicating a dead short right? But I wouldn't think the wire going to the jake on the valve covers is thick enough to cause this much power loss. Could I have a ground problem?
  5. When i let my foot off the gas to let the jake kick in I have a dead short somewhere I have ruled out it being the jake solonoids is there any other place where it could be rubbed through? And also when the jake is on my volt meter drops to about 13 volts from 14. Any help would be appreceated
  6. Funny thing went down to start the truck and see if i fixed the problem and it wouldn't start I have fuel to the pump just not coming outta the injection lines. Could this be the plug that goes into the pump or computer issue if I check it with a test light g is the only one with power and it's not constant it's on off on off I'm thinking this could be the reason I have a miss at high rpm?
  7. Better question where are the two ??
  8. Is that something I can fix or do I have to take it somewhere.
  9. The truck is a 1996 e7 427 at about 1600 rpm the truck will start to surge like its not getting fuel or the timing is off. New filters new lift pump any suggestions??
  10. Just turned out to be a stuck thermostat have been driving it for a while now and all of the sudden I lost my water temp guage not sure if its the sensor guage or a broken wire gonna do some chasing tomorrow
  11. Thanks for the info I will try that this morning and yes I am getting a bit of heat In the cab. I will let you know how it all turned out tonight.
  12. I just got the truck this weekend it had been sitting for a few months I topped up the antifreeze It was a bit low and it looks really dirty could it be a plugged water filter would this cause no circulation? I drove the truck for 1 load this morning and it worked fine then sitting idling while I was getting loaded is when it started to heat
  13. I have a 96 e7 454 it is running hot and there is no coolant pressure when I take the rad cap off doesn't matter weather or not I am pulling a load or empty or even idling still runs in the red. The bottom rad hose is ice cold and the top Luke warm anyone have a answer for me it would be appreceated
  14. i have a 2006 mack vision with a 480 motor 18 speed eaton and it seems not to have enough jam as it should we are on turbo #5 and was wondering if the 480 has a reputation for blowing turbos or is there something else wrong also is there anything i can do at home to make more power
×
×
  • Create New...