hicrop10
-
Posts
1,495 -
Joined
-
Last visited
-
Days Won
9
Content Type
Profiles
Forums
Gallery
Events
Blogs
BMT Wiki
Collections
Store
Everything posted by hicrop10
-
Cab mounts
hicrop10 replied to hicrop10's topic in Antique and Classic Mack Trucks General Discussion
The pictures are switched. -
Cab mounts
hicrop10 replied to hicrop10's topic in Antique and Classic Mack Trucks General Discussion
Here’s the pictures,1st is looking down from inside of cab,2rd is looking up from bottom.I can get the holes to lineup on the left side in the first picture.I am wondering if it just easier to cut out the whole mount area and replace it with a better one or to try and get the holes to lineup.
-
Cab mounts
hicrop10 replied to hicrop10's topic in Antique and Classic Mack Trucks General Discussion
mattb73lt,I am talking about the 2 mounts in the back.The 2 holes on top in the back don’t quite line up with the 2 on the bottom of the cab.I will walk out to the garage and get a picture of what I’m talking about.Been laid up last couple of days been in the hospital with some heart issues. -
I am in the very slow process of restoring my 64 B873SX.My question to all of you is are the cab mounts the same on the B80’s and the B61’s? I am mostly interested in the back 2,seems like the holes that go through the cab don’t quite line up with the holes in the plate on the bottom of the cab.I have access to a good cab off of a b61.
-
Did you try tapping the s/p switch with a hammer? It may be stuck.
-
Group Picture??
hicrop10 replied to Brocky's topic in Antique and Classic Mack Trucks General Discussion
I’m up here in Philadelphia just where is his show? -
Mowerman,you talked about seeing a Sunoco tanker spinning his wheels trying get out of the station.The problem they had was that the back rear was dead.They had problems even when they weren’t in snow the back rears were dead.Here in PA they would send them tractors to Florida for the winters,one of their drivers were telling me.
-
MACK Belly Dump
hicrop10 replied to 41chevy's topic in Antique and Classic Mack Trucks General Discussion
I think I have a piece of sales literature on these in my collection. -
Fuel Tank Rust Repair
hicrop10 replied to h67st's topic in Antique and Classic Mack Trucks General Discussion
First I’ve made up a fuel cap so I can put some pressure say about 5-8lbs of air and see if there’s and small pin holes. -
Fuel Tank Rust Repair
hicrop10 replied to h67st's topic in Antique and Classic Mack Trucks General Discussion
I have todo this on the tanks for my b87, problem being is the weight.I’m thinking of putting tank on work bench and just shaking it the best I can and doing some spinning. -
My b87 dragging our low boy trailer empty was around 3-5 mpg loaded with say a cat d9 dozer it 1-2 mpg.Engine was a Cummins 335.
-
Fellows check out West Cenral Auction co.They have an auction going on now that has 5 b models in the auction.They are pretty rough little to far to go from Pa.
-
No it most likely for a backup beeper.
-
Just to have,I would most likely part it out,since I have a b87.
-
Complete package.
-
Here’s the picture
-
Just got some pictures of the cab.It has a gas motor most likely seized.Floor looks great,there are some rust spots on the doors but nothing that bad.Will try and get some of the pic posted here.
-
I have only seen one picture of it so far.It does have all the glass in it.
-
The best of Biden will be when he is no longer in office.
-
I have a chance to pickup a cab for a b42.The owner tells me it has minimal rust.I haven’t seen it yet.What it worth.The frame was cut behind the cab.
-
I have a chance to pickup a cab for a b42.The owner tells me it has minimal rust.I haven’t seen it yet.What it worth.The frame was cut behind the cab.
-
Great to hear everything is good
-
Mack cab beige interior paint.
hicrop10 replied to JBushneck's topic in Antique and Classic Mack Trucks General Discussion
Tks,will be getting some spray bombs can of it. -
I am looking for the cab measurements for my b87,it would be the same as any b80 series truck.Trying to make a dolly to set the cab on,makes moving it around a lot easier.I have a blue print from the Mack Museum but it’s hard to read the back mounts measurements.Would like to lift the cab off as soon as I can.
-
Tks Bob and everyone else.The worse part is this just sitting around doing nothing drives me nuts.Have already called my union and waiting for the call back on my retirement.Tks again everyone.
BMT Forum Logo
