Jump to content

Vmac3

Bulldog
 View Profile  See their activity

  • Posts

    346

  • Joined

  • Last visited

  • Days Won

    2

 Content Type 

Everything posted by Vmac3

  1. Vmac3
    The red lamp is the engine shutdown warning indicator. May be because of low coolant, low oil pressure, high coolant temp etc.. Like Joey mentioned, find out what the codes are and we will try and guide you. V
  2. Vmac3

    Shop Talk

    Vmac3 replied to Onyx610's topic in Odds and Ends

    God almighty!!! My thoughts and prayers for a speedy recovery. V
  3. Vmac3
    Let us know what you find and doing to fix this issue.
  4. Vmac3
    No worries
  5. Vmac3
    EGR cooler efficiency fault. V
  6. Vmac3
    That blue "thing" looks an awful like a pressure switch for an A/C system. That does not look like a pressure or temp sensor. V
  7. Vmac3
    Also lets check the turbo shaft for excess play. These problems that you have sound unrelated. Also, remove the egr outlet pipe at the cooler. Check to see if there is any oil residue on the outlet side. V
  8. Vmac3
    Is there excess blow-by coming out from the blow-by tube? V
  9. Vmac3
    You would be correct Joey. Most of these were set to 650rpm from factory.
  10. Vmac3
    First make sure the parking brakes are applied and the engine is idling at temperature. Cycle the cruise control On/Off switch 3 times, the engine rpm should go down to 550 rpm. With the Set/Resume switch (its a spring loaded switch), toggle the resume to increase the engine rpm. Once you have set it to the engine rpm you want, press the clutch in. It should stay at your desired rpm. If its an automated transmission, then you would need Tech Tool to set the rpm. Hope this helps. V
  11. Vmac3
    Did you remove and inspect the engine ecu connectors as FJH mentioned? V
  12. Vmac3
    I would do what MP suggests first and see what happens. You spent a lot of money already. I'm wondering if you may be getting fuel in the engine oil causing your fuel pressure issue??? V
  13. Vmac3
    Egr blocked off? Ecm is looking for egr flow. It's probably derating the engine. Any codes? V
  14. Vmac3
    Had a 2005 granite with a broken baffle in the muffler causing high EGTs. Remove the exhaust pipe going into the muffler and road test it. See what happens. V
  15. Vmac3
    Turbo air supply air filter plugged? Seized vanes on turbo? Rockershaft plugs blown out? Seized rocker shafts? Charge air cooler leaking? Fuel pressure low? Fault codes? Engine oil level low? Oil pressure gauge not reading right? List can go on and on. We need more information. Let's start with year make and model of the truck. What has been done to the truck. What other symptoms are there. Lots of great minds here to help out. V
  16. Vmac3
    Makes sense. Injector metering and timing is critical to prevent excessive Nox production. The EGR doesn't flow as much as they used too and they figure they can clean up in the aftertreatment system. If the aftertreatment system is working as it should. V
  17. Vmac3
    Nox sensors have been an ongoing issue with the vehicles. I have found that if one has failed the other will surely follow. Just wondering, do the one box systems plug up with dried DEF still like the older 2 piece style? V
  18. Vmac3
    Wasn't there an update to the fan shroud and water pump that located it lower in the chassis? V
  19. Vmac3
    Its going to be money and time with my experience. If the checks that Joey suggested don't have an answer then you will need to invest some time and money. Disconnect the power leads to the jake heads and supply a fused switched 12V to each head. Drive the truck and get it hot. Apply your switch and see if they work. If they dont then you may have an oil pressure problem, a hardware problem or both. If they do then it may be an electrical issue. V
  20. Vmac3
    Hello everyone. Its been a while, back from vacation. The D12 had the gauge as well. It was positioned to the "A position" on the gauge and the 11-13 and 16 used position B. Whenever I do/did a camshaft job I always ensure that the engine is set to TDC. Zero on the flywheel housing and TDC on the camshaft. Make sure you have the correct backlash between the idler and the cam gear, otherwise you will have serious issues. V
  21. Vmac3
    Does this happen when the truck is pulling a load or getting up to speed? I've had suspension leveling valves cause all kinds of grief. V
  22. Vmac3
    Intake and exhaust section and I believe its under miscellaneous.
  23. Vmac3
    Any part of the suction side of the fuel system will draw air in. Seen fuel water separators cause this a few times and corroded block off plates where the primary fuel filter would sit. V
  24. Vmac3
    Fuel diluting the engine oil. Good call Joey. V
  25. Vmac3
    Maybe the Mods here can put a separate section for him where people can visit to have their problems solved. I don't know, maybe call it "Ask Len. Your One Stop Shop For Problem Solving. Cuz I've Been There, Done That". V

BigMackTrucks.com

BigMackTrucks.com is a support forum for antique, classic and modern Mack Trucks! The forum is owned and maintained by Watt's Truck Center, Inc. an independent, full service Mack dealer. The forums are not affiliated with Mack Trucks, Inc.

Our Vendors and Advertisers

Thank you for your support!

Mack Related Links

Popular links

BMT Forum Logo

HTML tutorial
×
×
  • Create New...