JoeH

Swim; haven't had time to put our lettering on the side of the mixer body, that's just one thing on the long "to do" list. More important is the brake S cam bushings are worn. Truck will be getting cam bushings and new slack adjusters soon, I have to adjust the brakes every morning.

Do you have a VIN? A Mack dealership would be your best resource. They'll ask for the "last six" of the vin, but you'll want to have them run the full vin as it will likely have a different country code or something weird.

How's your Pyrometer reading? How about your Boost gauge? We just replaced the charge air cooler on our '95 E7-350 and it's a night and day difference. Picked up 10 psi of boost and dropped 2-300 degrees on the pyro. Had a cracked charge air cooler.

All reassembled and operable. Tomorrow is "Sink or Swim".

.010 is if you're using a Machined Dowel type runout gauge that fits into the engine in place of the crankshaft. .020 is if you're bolting a runout gauge to the crankshaft. The difference in runout tolerance is because of any wobble in the crankshaft/bearings. According to the book.

No idea. Depends on how big your hills are and how heavy your foot is.

That makes sense.

Allison Auto & torque converter bolted to the flex plate. Not sure how much "slop" the Allison input shaft can tolerate.

Inline pumps can be computer controlled from ~1991 on. It's called econovance or something. Drive hub for the fuel pump is electronically controlled via VMAC I and VMAC II computers. About 1998 is when it went full computer with the EUP fuel pumps. I have 2001 in my head as the best year for the ETECH motors. The E7 can be full mechanical or partial computer controlled. You have to look closely at the fuel pump assembly to figure it out.

Mechanical E7s are probably the best Mack motor ever for durability. Personal opinion. Computer E7s... Good engines but electronics fail...

My dad cut out around 7, I put in another 4 hours trying to get dumb stuff done that doesn't need 2 people. Remaining: Trans mount bolts Battery cables to new starter, tie up wiring PTO shaft & drive shaft Rear oil pan bolts/readjust gasket Reinstall the water tank for the mixer body

If I have to take this apart again it's to drop a reman engine into this truck. Will run it til it says otherwise...

Currently scraping the last of our bottle clean to torque up the bellhousing/flywheel housing bolts.

I would have much rather had the Mack brand flywheel housing, but Mack has yet to get back to me on an ETA. First Motion part number from online matched the Mack number, but noted that it wants 7/16 bolts for the flywheel to bellhousing, not the metric ones that Mack had. New flywheel housing is within 1/16th overall depth of the old one. Overall I hope I'm not screwed. Trans is bolted up, torque converter is bolted to flywheel. Time to torque up some things and keep working.... Late night...

Left dowel is a solid round pin. Right dowel is a flat blade.

Top left. Top right. Bottom left. Bottom right.

Broken lower right flywheel housing to block bolt. How do we adjust flywheel housing runout? 0.022, 0.000 0.028, 0.013 Those are the runout readings on the four corners.

Macks don't respond well to deletes.

https://www.firstmotionproducts.com/mack-flywheel-housing-634gc5337m2/ Found one here. Getting started on replacing it tomorrow morning.

https://www.firstmotionproducts.com/mack-flywheel-housing-634gc5337m2/ Called these guys this afternoon at 2:30, talked to Dale. Top notch fellow, he had 2 in stock in their Allentown PA warehouse. Paid $1200 over the phone, made the 50 minute drive and picked it up before the warehouse closed at 3:30! It's aftermarket, no name on the casting and there's minor differences, but the part number they listed is a dead match to the "old" part number Mack gave me. Will very carefully compare it to the old one as we tear it apart. It's my understanding that there's different depth flywheel housings. We have the engine rebuild book, so we will do what we can regarding "alignment" as there are adjustable dowel pins or some BS.

Dex?

Had the truck out on the road for a few days before the Temporary Registration expired. Runs & drives very nicely. As rough of a ride as it was back from Iowa it's completely the opposite locally with weight on. Rides very nice. The flywheel housing is cracked six ways to Sunday. Waiting to hear from Mack if they can get me a new flywheel housing any time soon, otherwise I have to find a used one. Filling wheelbarrows at a job

I have a request in through my Mack dealer for a flywheel housing for our (new to us) 2003 MR688S. Has an AI350 with an Allison HD4560. Old flywheel housing has a decent amount of cracks all over it, visible externally. If my dealer can't get me one for a few months does anyone have a good used one?

Are those bolts clamping the trunnion bar in place? Is that how the stand was set up originally or did he add that?...

Not sure what the road call was, but you have to have a minimum. Every job has to cover it's expenses, including putting food on your table. The guy that bailed me out of trouble in Illinois charged me 400+ to show up, swap my lift axle tire onto a drive position, and rewire my fender lights. Took 2 hours total. Was worth every penny. You have tools you've bought, a work truck to insure/maintain. You've put a lot of money out to be in business, you shouldn't be making Walmart employee wages.