Jump to content

jackdk

Bulldog
  • Posts

    55
  • Joined

  • Last visited

Everything posted by jackdk

  1. Does anyone have a set of these laying around they want to part with. Mine are so badly deteriorated, that I need to replace both of them. 1985 up Mack Superliner. Thanks,
  2. I'm sure it was moved for a purpose Terry. When I had an issue of running out of fuel going up hill with less than 1/2 tank. I looked inside and saw that the baffle had come lose, and was floating in the tank half way up. It took out the tank float, and it probably rubbed a hole in the pickup tube, so he moved the draw to the bottom front. No wonder the previous owner filled the tank with fuel when I came to look at it, so I wouldn't see the baffle floating in the tank. LOL
  3. Thank you Hans. The pipe thread end into the tank, is one 3/8" and the other 1/2", or are both fittings into the tank 1/2"?
  4. Does anyone have these two 90 degree fittings laying around they want to sell. I'm installing a new fuel tank on my Superliner, and these are not on the new tank. My tank, the original owner moved the fuel feed to the bottom front of the tank, and I run out of fuel climbing a hill when level is less than 1/2 full. Or, if someone knows the part number, or the exact size and dimensions, one flare, or both ends flared. They are both different sizes for feed and return. Thanks, (not my photo-just to show the fittings needed)
  5. I am in need of a nice cowl vent for my Superliner. Any vent off an A/C R, RW, DM etc. Mine is nice, but must be off a newer model as its all plastic. The power of the actuator did a number on the tabs on the underside of the vent door. Thanks
  6. Does anyone know, or have a good part number for the fuel tank sending unit that was used on a 1985 Superliner with 25" diameter tanks? I imagine the CH or MH with 25" tanks used the same one. After searching 100's of senders, I just can not find anything listed for RW 25". I do find RW units for 22", but thats not going to work. Thanks in advance,
  7. Has anyone purchased and installed this firewall insulator pad kit from Quiet Ride Solutions. Was wondering about the quality, fit, and did it deaden the sound at all. Thanks
  8. OK, no problem, and I do appreciate what you already sent. Thanks again.
  9. OH MY! BROVO Vladislav. That is absolutely perfect. If its not to late, do you have a closeup picture of the horn valve and bracket. I have a feeling the previous owner took out the bracket
  10. Do any R, RW, DM, etc members have their headliner pulled done to get me pictures of the location of the airhorn valve, bracket and location? The previous owner removed the lights, horns, and roof vent from on top of the roof. I partially pulled down my headliner to day, and I can not figure out where it would even go. Has to be near the grommet in the headliner in assume, but I can not find anything that looks like the original location Pictures or factory diagrams would be fantastic. If there are part numbers (valve, bracket, lanyard etc) for any of the items, that would be a BIG help as well. Thanks in advance, for any help, picture, or part #s.
  11. Sounds good Joey Mack. Might be good to stock up on that stuff. Thanks.
  12. Thanks MackTech. I guess the best thing to do is when I remove the hoses, cut it, and measure the inside diameter to see if its 3/8 or 1/2. Not sure what has been done to this truck before I purchased it, and what mods its been through. I know a lot has been done. Started as a tractor, then stretched and made into a tri-axle dump, air to the rear for pintle hitch trailers. Thanks again.
  13. I am getting ready to replace my front brake chambers on my 1985 Superliner. My question is the rubber hose size. Not sure if mine are 1/2" or 3/8" hose, but are about 18" long. What doesn't make sense to me is, why do they both go through a 3/8 fitting. What is the advantage of 3/8" fitting to 1/2" hose to 3/8" fitting over a 3/8" fitting 3/8" hose 3/8" fitting. No matter what size hose you use, it still narrows down to 3/8" I want to make sure I put the correct ones on. All my drop-down hose are so old, that all the markings and sizes on them are long gone.
  14. Last week one of my hood restraint cables snapped on my 1985 Superliner. From what I found, its part number 27RC250. I can't find one anywhere, and I don't see any cross reference numbers for it either. Anyone know where I can find, or have one they want to sell? If the other one brakes, I'm in trouble. Its a total of 38" forked clevis to forked clevis. Thanks...
  15. Looking for two decent, not cracked or repaired R-RW dash bezels in silver/grey color. I need the bezel that holds the tach and speedo. Part # 8MT519 and the top dash that holds the ash tray # 370R5114. If anyone has any laying around that need a good home, please let me know condition and what you want for them. Thanks...
  16. Yah, I spec one out with Alumitank. 25x59 Polished, shipped to the house was a bit over 1300.00. Might be the way to go.
  17. OK. That sounds easy enough. Thanks for the info...
×
×
  • Create New...