Jump to content

steeler

Big Dog
  • Content Count

    167
  • Joined

  • Last visited

Posts posted by steeler


  1. 2 hours ago, c-mac said:

    I've pulled the differential pressure sensor and used a small drill bit by hand to remove the carbon buildup in the two ports in the mounting bracket , when I figured I have cleared the mounting bracket I took a spray nozzle straw and pushed it into the venture

    That's what I normally do on other applications, but this one has the ports making a 90 degree turn down inside the hole so I can't get anything to eat thru it.

    I tried carb cleaner which I've had luck with in the past, but it didn't help. I just put it back together and told the customer that he will have to deal with the yellow light until the part comes in. We ordered it as unit down, which usually speeds up the process. Hopefully it won't take a month.


  2. On 9/3/2019 at 3:11 PM, c-mac said:

    Yes it has a/c the new fan clutch is on at all times with the harness to the clutch disconnected. I’d really like to see the diagram if it shows wire number and numerical pin placement 

    Sorry for the delay, crazy busy lately. I'll get that for you tomorrow!

    Hopefully I can find it.


  3. 8 minutes ago, Steve 97 said:

    Ya we have one kit here just wasn’t sure if adding the oil lines would solve the problem 

    I don't think I've ever successfully fixed one with just the kit, but have fixed many with kit and lines. Do both. Make sure you have the new style oil feed screws, and remove the little ball and spring from the bottom.

    The kits usually had instructions in there.


  4. Be careful messing with the gov. 

    The rule of thumb I always used when bumping them up was to screw the star wheel as far forward as it will go, then slide the plate forward about the thickness of a dime. That will make them pull stronger and dump more fuel sooner, without waiting for the boost to build.

    I've never messed with the springs though.


  5. Well I found the problem. Pin 16 on the control panel is a ground, I was getting just enough of a ground to operate everything but the compressor. So after running a new ground I have good power to the compressor, but the clutch is toast. Oh well at least it'll be working tomorrow!


  6. 10 hours ago, 41chevy said:

    Eliminates alot with that info. Does you diagram show the compressor circut tied in with powering the engine fan?

    It shows that as separate. It has a separate pressure switch that sends is signal to the ecu for the fan. Didn't have a chance to work on It today, probably in the morning.


  7. 8 minutes ago, 41chevy said:

    One of the fuse /relay panels has an AC compressor relay that supplies power.  Also the low pressure switch the prevents the compressor from kicking in with less than 50 PSI in the system so I would also put a set of gauges on and check the pressure in the system for starters. 

    Should have mentioned that I replaced the condenser due to a leak. I've also tried a new control panel and new temp sensor as well.

    I don't have any fuses or relays that are labeled specifically for the compressor. There are a couple others that are marked HVAC, but they are powered and good. 

    I did find a different diagram than the one I was using, it's showing power to the compressor coming directly from the control panel, unfused. I'll check for continuity on that circuit in the morning.


  8. 2014 GU713, I've got no power to the ac compressor. My wiring diagram is a bit outdated so I'm not sure I'm going in the right direction.

    My diagram says fuse 53 is for the compressor, but the sheet in the fuse panel shows 53 as a spare. There was no fuse in it, and three is no power to it, even though it is pinned.

    So does anyone know where the power comes from? I know it goes to the pressure switch, I have continuity from switch to compressor, but no power.

    Thanks for any help guys.


  9. On 6/25/2019 at 3:35 PM, CCMtruck said:

    Update: Just like steeler said. I found aluminum pieces in the inlet side of the ecm cooler plate. Its the simple stuff we forget sometimes.

    Good deal. Glad you found the problem!


  10. Kinda off topic here but we do quite a bit of work on paccar engines. You wanna talk about an SCR nightmare, wow.

    I had one with a def quality fault that just would not clear. I threw everything under the sun at it, nox sensors, def doser, new def fluid, dpf filter, catalyst, 7th injector, countless hours of troubleshooting and test driving all to no avail.

    Ended up opening a case with paccar engineers and after several regens and 2 40 mile test drives that had to be recorded and send to them, they simply gave me 24 hour special access to a feature in the software that allowed me to clear the code out.

    I mean really? After all that, it was that easy? I wish they'd give me that special button permanently!

    The truck worked fine after that for about a year, then the same crap started again. The customer said screw it and had it deleted, and I don't blame em.

    • Like 1

  11. Ok after going thru it all again, I can disregard that 33 fault code. I was using a pro link and had the vmac1 cartridge in it. I hooked up the laptop and it's actually a 32, for the rpm sensor. I've eliminated the wiring and sensor, so I believe they have the wrong flywheel in it.

    I don't know who was working on it before but damn, let's just say he was a hack.

    Sad thing is, I'll probably never know what the outcome is. The only reason it's at my shop is because nobody else could figure it out, so the customer is going to pull the flywheel out himself.

     


  12. 16 minutes ago, Mackpro said:

    Mack came  out with a conversion kit to replace the  two VMAC 1 ECM’s  with a single VMAC 2 ECM . The wiring harness on the engine remained the same as original. Chances are the one of the original VMAC 1 ECM’s failed and the conversion kits was installed. 

    Hmm. Interesting. Ya everything I'm looking at other than the module screams vmac 1. But I checked the vin and it is coming up as vmac2. The pump part number is correct.

    I got more info on this truck. I noticed it has a new clutch and flywheel somebody else put in. I'm now suspecting they may have the wrong flywheel and the rpm sensor is not reading it.

    The engine will die if I unplug the tem at the pump, but runs the same with the rpm sensor unplugged. That tells me I've got something fishy going on with the rpm sensor. It's supposed to ohm at 200-300, but I've got 180. It's a PAI sensor, I'm going to put a Mack sensor in it and see what happens.


  13. 20 minutes ago, Mackpro said:

    Here’s the easiest way to tell a VMAC 1 from a 2  on a CH style truck .  A VMAC 1 has the engine harness plug iinto the firewall right above the windshield washer fluid jug on the passenger side of the firewall. On a VMAC 2 truck , there is a block off plate above the windshield washer fluid jug . Also  , the Econ-Vance is a lot longer on a VMAC 2  and the injection pump almost touches the air compressor, and  of course the VMAC 3 is an ETECH  style engine with the heat shielding  over the individual injector pumps 

    Thanks pro. I'm not with the truck right now but I do know there is a bulkhead harness going into the firewall on the passenger side. I remember that was how I could always tell a 1 from 2, but I couldn't remember which was which.

    So, sounds like a 1, so why does my module have a vmac 2 sticker on it? Didn't the 1s have an fic module?

×
×
  • Create New...