Jump to content

topo

Bulldog
 View Profile  See their activity

  • Posts

    91

  • Joined

  • Last visited

 Content Type 

Everything posted by topo

  1. topo
    I remember using 4 671 Detroit's on a mud pump on a drilling rig and one rig had 2 8v71 on the rig one Motor had electric starter and the other had a air starter the clutch was air later when one motor failed it was changed was changed out to one 12 V71 .
  2. topo
    Your first post reminded me of trouble I have had with fuel lines when using braded fuel lines like Aeroquip the very thin liner inside the hose would separate and collapse and seal the hose closed when driving because the pump is pulling more fuel after it stopped running and not drawing a suction it would open back up and restart and run ok till the pump suction increase would collapse the liner again . the place where this would happen the most is if the fuel line was inside the frame where the exhaust was near the line .
  3. topo
    what is a vmac and ficm ?
  4. topo
    I worked in the oil field and have quit and found a new job drilling for joe leaves a bad taste in my mouth .
  5. topo
    The filter housing on the table uses the Baldwin filter # P-706-m The filter on the engine uses the two filter one on top of the other ( Baldwin P194 ) there is a hydraulic filter (P194 HD ) both housings have one inch ports in and out .
  6. topo
    The Baldwin filter # P706-M the gasket is a O ring and I don't have a number for it .
  7. topo
    when you get the filter get a new O ring
  8. topo
    A 5 speed main and 4 speed auxiliary work very well .
  9. topo
    I Thought from the factory they all had Mack transmission because of the high torque ?
  10. topo
    I could have made the same mistake thank you for sharing .
  11. topo
    Maybe the bottom of the cab is twisted and that is causing the doors to not function as they should . also there is no cross member under the fifth wheel that I can see maybe other bracing was left out to save weight and the frame rail is pushed back causing the cab mounts to be in line .
  12. topo
    I remember just bolting the pads to the shoes do they not do that any more ?
  13. topo
    I have a military trailer M269 made in 1954 It was made by the Pressed steel car company and I was wanting to know more about where they where located and what else they made before WWII when the war was going on and after the war or any thing some one may remember . Thank you
  14. topo
    I just read where Biden put Harris in charge of protecting voters rights if that true sorry I don't know what to say .
  15. topo
    looks like the same suspension used on a 43 White 666 I can't find any model numbers other then Timken in my books .
  16. topo
    Rob Thank you
  17. topo
    I have lantern with two mantels out side and was thinking of using DOT tubing to run a line from the regulator to the lantern about 20 feet . any thoughts on this ?
  18. topo
    40 Executive orders You have to think someone else is writing them for him . with troops at the capital it looks like someone is paranoid about losing what it not really there's
  19. topo
    What will they reinvent next The electric switch it turns something on or off it needs a price cap of no more then 4 bucks no mater what it turns on or off or how it dose it .
  20. topo
    I saw an the news that 10,000 to 20,000 national guard troops will be on hand for Biden's big day to protect from the home grown terrorists . That right there looks like voter fraud .
  21. topo
    The press really has ugly names for the American people there today visiting a public building I did not see any monuments pulled over and burned . I feel like I was threated and should not question any thing political .
  22. topo
    I would say by seeing the rope rail around the bed this truck was used to haul drilling mud .
  23. topo
    Thank you I will just leave it alone it may have never been taken out .
  24. topo
    I was planning on adding a coolant heater to my Mack 673 by removing the large round port above the starter I made a tool by cutting a large washer and welding it to a socket to get a good fit but it won't unscrew so them I may go with a tank style heater . any thoughts ?
  25. topo
    In the mid 80's I bought a 53 GMC with a 302 and when replacing a leaking valve cover gasket I found a very dirty top end the engine had been rebuilt in the 70's . Then a few years back it started leaking antifreeze and needed a head gasket I removed the valve cover and the top end was clean very clean I pulled the side cover the lifter also clean I had the valves done when the head was off then put it all back together I never scraped or wire brushed anything it was so clean the only oil I had used as Rotella 15-40

BigMackTrucks.com

BigMackTrucks.com is a support forum for antique, classic and modern Mack Trucks! The forum is owned and maintained by Watt's Truck Center, Inc. an independent, full service Mack dealer. The forums are not affiliated with Mack Trucks, Inc.

Our Vendors and Advertisers

Thank you for your support!

Mack Related Links

Popular links

BMT Forum Logo

HTML tutorial
×
×
  • Create New...