Jump to content

CCM

Puppy Poster
  • Posts

    29
  • Joined

  • Last visited

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

CCM's Achievements

Explorer

Explorer (4/14)

  • First Post
  • Collaborator
  • Conversation Starter
  • Week One Done
  • One Month Later

Recent Badges

0

Reputation

  1. The customer had me on hold with this unit and now want's to continue with diag. Has anyone come up with any ideas with what could be the issue. Now for some reason I am unable to even reset the soot level. I've even checked for any ecu updates. Head scratcher!!
  2. Thanks Mackpro. I appreciate any help
  3. Can you run a crystal sublimation test even if the truck doesn't have DEF?
  4. We had the filters cleaned and reset the soot level and reset back to 13% and after the first failed regen it jumped to 140%. We have tried to reset the soot level and won't reset. We have performed several regen's and soot level never drops. The diff pressure is at 0.27 to 0.29 psi. I have previously replaced the 7th inj due to an open circuit and have even removed it and cleaned it to be sure. The adaptive factor was reset. After the regen ends no other codes appear. Thanks for the response.
  5. I always recieve some good info here so i need help again. I'm working on a "09" Mack CXU613 (MP7) A few months ago we replaced all 6 injectors and not long after that we had to replace 2 due to fuel leaking from the bodies. All was working fine but came back with mid 128/psid 47/ fmi 0 and soot level codes. Checked regen system,found tee check valve at A/T fuel inj faulty. Replaced the check valve and all was good again. Returned again with same codes. Tried running regen and would not build temp. Removed dpf and sent to be cleaned. Reaseambled and ran regen. Still not temp. Have fault traced with G/D. Replaced egr valve. checked diff sensor,tubes,vgt lever,boost leaks,fuel pressure to A/T fuel doser and made sure it wasn't plugged. During regen the exh temps are (inlet 739) (after cat 969-978) (outlet 877-904) It goes back to idle and soot level reads the same and only code active is for soot level. I'm heading towards faulty DOC but who want to spend 5k on a guess? Any ideas?
  6. Thanks turckster l’ll look it over
  7. 2010 MACK CXU613 MP7 with oil pressure red warning light coming on and shutting down. The oil pressure gauge continues to read. Oil pressure sensor has been replaced. #22899626. Anyone run into this issue?
  8. Still working on this overheating issue. Can't seem to get a clear cut answer on if you should hear the fan when PTT is showing engagement at anywhere from 86% to 99%. Coolant temp will run as high as 223 degrees with the fan showing lock up but wont cool the temp down. If the harness is disconnected so the fan runs constant you hear the fan and the temp stays normal.
  9. Trans is a EATON autoshift. Took off a behr fan clutch #21046590
  10. Anyone have any info on the electric/viscous fan clutch for the MP7 engines. The customer is complaining of the engine running warm and the fan doesn't come on soon enough. We have updated the clutch to part #85115602 if that helps with trying to find info or some kind of a bulletin. Maybe it's a programming or parameter setting? We have also replaced the water pump and thermostat. The radiator was replaced not to long ago also. As long as you have to electrical unplugged and the fan runs constantly it cools just fine.
  11. Troubleshot for 4094 code. Monitored while performing regen and towards the end of the regen the Nox levels were still at high 200 to low 300. Recommend removing the egr cooler and insp?
  12. @Mackpro, Thanks for the info
  13. Working on a 2012 MRU613 mp7 with non-catalyzed system. I have a constant returning code of SPN 5246/FMI 0, SPN 4094/FMI 18. Replaced def doser nozzle. checked egr valve for flow while unplugged. (has slight flow) Checked diff sensor and checked ports for plugging. Not plugged. I can perform a regen and codes become inactive. Truck will return within a few days with same issue. Just replaced Nox sensors due to updated part number and road tested unit (max hill grade is 15%) while monitoring Nox readings. Nox intake always showed 0 and Nox outlet varied between 236 to 510. Anybody have an idea on what the Nox levels should be?
  14. So, we performed the glove test on the egr and it did inflate the glove. replaced the egr valve and re-tested. It still put air into the glove but not nearly as fast. Still getting a lot of black smoke. I's it possible the intake manifold and intake ports are just filled with excessive soot and is going to take time to clear out?
  15. @Mackpro, Thanks for doing the research. there were no Injector codes or any fuel related codes. That's what has us puzzled. The egr valve does have the updated one on it already (no drain) @Turckster, We did checked for any flow but we haven't tried the glove trick. We will try that this morning and see what we come up with.
×
×
  • Create New...