I have a 1954 Model B 42 that I have been working on over the past 10 years (way more off than on). I am at the point where I want to mount the Radiator onto the radiator support along with the grill and rubber seal. It has been so long ago since I took it apart I forgot where the rubber seal goes. It doesn't seem right that the rubber g...
Welcome to BigMackTrucks.com
 |
Welcome to BigMackTrucks.com, the best resource on the Internet for Antique, Classic and Modern Mack Trucks!
Please login or register to take advantage of everything BMT has to offer. Memberships are Free and offer many benefits:
If you are having trouble logging in or haven't received your validation email, you can post as a guest in the Guest Forum.  
|
Guest Message by DevFuse
Recent Entries 
-
B 42 Radiator mounting issuesrowdav's Blog
21 May 2013 -
Day seven? oh god knowsstephenellis' Blog
17 May 2013 -
Day fivestephenellis' Blog
15 May 2013 -
Day fourstephenellis' Blog
10 May 2013 -
Day threestephenellis' Blog
05 May 2013 -
You spin me right round !stephenellis' Blog
05 May 2013 -
Day threestephenellis' Blog
05 May 2013 -
-
Day twostephenellis' Blog
03 May 2013 -
Another productive day....Once we got the engine a bit cleaner it was time to see what I have gotten myself into. Trying to turn the engine over by hand sucked so the starter came out without much problems (it is bloody heavy tho) as I had popped my 12v booster pack on it in the hope that it would turn over but no luck. Once on the deck and cleane...
I have a 1994 mack triaxle dump truck,350 engine,8LL transmission,been sitting a little while, tryed to move but not getting air to brake valve on dash any ideas what I might check would be thankful,looks like a few air lines have been messed with under dash, when I do supply air to air valve from another souce, transmission only goes into high, before it...
What is the best type of coil over springs i can fit to the rear of the cab of me titan to assist the existing airbags and cab shockers .
I have a 2000 Mack with an E7 engine. I have a new three piece exhaust manifold to put on truck. Does anyone know if there is an assembly joint compound or some kind of sealant that should be used between the pieces or should I put them together dry and let them rust together ?
I drive a mack rd 800, 400 half mechanical half electrical fuel pump and when in a pull going up hill with a load the fuel pump shuts off when the computer is trying to feel fuel. could anyone please help
Mack 1975 RS700L V8 for sale asking $13,500.00 or best offer
Posted by
truckingisallme
in 1975 Mack RS700L V8 for sale,
19 April 2013
·
227 views
I am selling my 1975 Mack RS700L V8 end dump. Truck is in great mechanical condition. I'm unsure of the actual mileage being I just fixed my speedometer. I am the third owner of this vehicle. Both owners had their own work done to the truck for road legal repairs. Rear ends rebuilt in 2009 that I have documents for. A little about the truck. It's again a...
What should my Air Lifter gauge be reading (how many psi) when I have load and when I am empty. I have a 2005 Mack CV713 Granite.
My fan isn't working for a/c and heat. I don't have a fuse diagram to show me which one it is. Does anyone know where I can get a diagram from or any suggestions.Thanks!
Hey All...I am in the aluminum scrap metal business. I have the option of purchasing over 200k lbs. of 1980 Mack Transmissions & motors.I need to know approximate percentage of Aluminum per trans & motor. If anyone can offer there expertise I'd greatly appreciate it. Thank you,AL Guy
Having an issue with the compressor recirculation valve. I hooked the computer and it says that it is shorted low or open cercuit. I'm looking all over and I cant find or identifiy this item.
New to this. Have a 2004 Mack with a 460 ASET, pretty sure it's the AC because it has the EGR cooler. Been have some problems with it and are pretty sure that it is the EGR valve and possibly the cooler. I know that with the 08 and new you can delete the emissions but i can not find a way to delete them on the ASETs. Was wondering...
I have a MP8 motor in a 2009 trident done 160,000kms and the injector tubes failed i replaced them and only lasted another 20,000kms this is not a cheap job is there an upgrade for these around i am considering ditching the motor and putting in a used cat
2008 MP8 engine
Posted by
tryingtomakealiving
in tryingtomakealiving's Blog,
12 March 2013
·
461 views
Working on 2008 Mack with MP8 overhead cam engine. Ive got problem where the gear on air compressor keeps getting chewed up. Removed tranny from truck and removed timing gear cover from rear on this engine. Found the intermediate idler (double idler) gearset rubbing into aluminum timing cover. Wanted to know if anyone has come across this problem before.
We are starting to replace the cammel back spring on a quad dump truck. The labor cost at the mack dealer is $2600.00 and $2400.00 parts to replace springs and all hardware. Is there any tricks to doing this job or anything a fella should know before starting.
Can anyone tell me what 2002 Mack Freedoms are like?Are they worth buying?What kind of mileage do they get?Does the engine and automatic transmission hold up well? ThanksCasey
The plastic tabs that hold the inserts in the center dash are breaking off on my RD688S. Is there a way to repair it without replacing the dash? Or is there an aftermarket dash or insert I can put in there?
Does anyone have any tips on em7 cam /lifter removal
One of my Dump Trucks was involved in a major frontal collision. The front bumper, Hood, Rad, and Driver Side steering arm were damaged. Otherwise, no other visible or mechanical damage was observed. The Mechanic believes all mechanicals have been repaired but the engine would not start. We have two different electricians have a go at it and nothing...
Chevy's global expansion has prompted the automaker to go with a new marketing slogan. Automotive News reports that the new Chevy mantra is "Find New Roads." Will you be trying to buy or sell a new or used van? If this describes you, get a quote at CarDealExpert.com. New methods for Chevy Chevy has a plan to push new goods into 140 worldwide markets...
- 234 Total Blogs
- 604 Total Entries
- 1,287 Total Comments
- rowdav's Blog Latest Blog
- rowdav Latest Blogger
0 user(s) are online (in the past 15 minutes)
0 members, 0 guests, 0 anonymous users
